Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. Disconnect the power cord from the rear of the product. sureeeeeeeee. http://orgias.org/hp-psc/hp-psc-1315v-check-print-cartridge-error.html
If the issue persists, continue to the next step. Check the paper loaded in the paper tray, and then make a note of the paper size and type. Open the cartridge access door. Figure : The door pins Reconnect the power cord to the rear of the product. http://support.hp.com/us-en/document/c00094661
Any one have a suggestion? Try the intended task again. Continue with the steps below - you must perform the steps on both cartridges. Step 4: Clean the problem cartridge contacts If the light is still blinking, clean the electrical contacts by the procedure below: Gather the following items to clean the cartridge and print carriage: Clean distilled water.
Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 10-05-2013 03:17 PM Yes, same error.Check ink cartridge indicator is flashing.THanks for taking the time to respond.IAn Reply 0 0 DevRao Distinguished Professor Posts: 3,234 Member Since: 02-03-2010 Message 10 of 10 (2,008 Views) Report Inappropriate Content Re: I have a print cartridge error with my HP PSC 1315 all-in-one. [Edited] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 10-07-2013 08:19 AM - last edited on 04-20-2016 09:42 AM by OscarFuentes Hi insanegain,Please refer the link below to troubleshoot the issue.http://support.hp.com/us-en/document/c00095908 Although I am an HP employee, I am speaking for myself and not for HP.--Say "Thanks" by clicking the Kudos Star in the post that helped you.--Please mark the post that solves your problem as "Accepted Solution" Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10 Upgrade, Printer Does Not PrintHP Printers - Using Google Cloud Print with Your HP PrinterHP Printers - Printer is Offline (Windows)HP Printers - Resolving Printhead Problems and Ink System Failure Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP. I called HP, my warranty is over. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Hp Psc 1410 Check Print Cartridge Flashing Step two: Test the connection Press the appropriate button(s) on the product again to perform the intended task.
The product prints a self-test report. Hp Psc 1210 Check Print Cartridge Error The carriage moves to the center of the product. Solution four: Clear any jammed paper Follow these steps to clear a paper jam from the product. http://h30434.www3.hp.com/t5/Inkjet-Printing/hp-psc1315-suddenly-gives-me-a-quot-Check-Print-Cartridge/td-p/1562999 Figure : Disconnect the power cord Wait 15 seconds.
Try the steps below to identify the problem cartridge: Open the cartridge access door. How To Reset Hp Psc 1410 Printer Do not use paper that is bent, torn, dusty, damp, wrinkled, curled, or paper that does not lie flat. If the printer is connected to a computer and the HP software has been installed, one of the following messages is displayed: The cover is open The print cartridge on the right side of the carriage is missing, not detected, or incorrectly installed The color print cartridge is missing, not detected, or incorrectly installed Print cartridge error Step 1: Close door If the cartridge access door is open, close it. Figure : Disconnect the power cord Remove the rear access door.
If the issue persists, continue with the next solution. http://support.hp.com/us-en/document/c00095908 Solution five: Test the power with a compatible power cord from a different All-in-One If you have another available power cord that is compatible with the product, use the alternate cord to test the power. Hp Psc 1350 Check Print Cartridge Reply 0 0 stevinsonboy Tutor Posts: 17 Member Since: 01-03-2011 Message 4 of 10 (2,541 Views) Report Inappropriate Content Re: I have a print cartridge error with my HP PSC 1315 all-in-one. Hp Psc 1350 Troubleshooting Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults.
Then slide the cartridge out of the carriage. his comment is here Figure : Close the cartridge access door Check the product control panel for blinking lights: If the On/Resume light () blinks, replace the color cartridge. Unplug the power cord from the wall outlet. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 06-01-2013 07:16 AM Hi out there!I have the same problem with me PSC 1315 xi.This is very frustrating because I just purchasenew set of cartridges and this problem rmain!Based on the fact that now I m noticing on thisBlog that allot of peopleare having the sameproblem. Hp Psc 1210 Troubleshooting
HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend possible solutions. This video shows how to print a test page Click here to see this video in full screen on YouTube. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 03-09-2014 10:13 PM So somehow the "Check Printer Cartridge" error stopped blinking and you got it working?? this contact form Plug the power cord back into a wall outlet.
My printer was working fine 3 nights ago, 2 nights ago I started having this problem. Hp Psc 1350 Manual Any other suggestions? Step one: Install the cartridges Press the On/Resume button () to turn on the product.
If these steps resolved the issue, you do not need to continue troubleshooting. Help! The product prints a self-test report. Hp Psc 1350 Error Code E Solution two: Load paper Follow these steps to load letter or A4 paper into the product.
Press lightly on the top of the cartridge that you are replacing to release it from its slot. Figure : Insert the cartridge Firmly push the cartridge in until it snaps into place. Wait until the On/Resume button () is steady. navigate here The sequence must be completed within 10 seconds.
If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. Solution two: Cancel and then retry the task Follow these steps to cancel and then retry the current task. An obstruction is blocking the paper path. Wait until the On/Resume button () is steady.
If the product does not turn on automatically, press the On/Resume button () to turn the product back on. Put the ink back in it one at a time and try to print a test page. Bob,After I wrote my last - It failed again!!I have taken the rather drastic step of stripping down the printer - (not to be encouraged, and care must be taken when lifting off the top cover - there are two strip contacts connecting the top with the bottom) - and completely cleaning all parts both moving and static.The dirtiest part was the two beds that the cartridges are cleaned on - there was a considerable build up of dried ink.Having put all the parts back in their respective places (I think!) I went to the print toolbox and aligned the cartridges and then cleaned them. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 01-07-2013 02:50 AM Though the inklevel should be sufficient only the colour cartridge HP 57 shows so where as the b&w HP 56 doesn't.
If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. Use only one type of paper at a time. When only the On/Resume button () is blinking, release both buttons.
Reach inside the product through the cartridge access door, and then manually move the carriage. note: Remove paper as carefully as possible.