Any one have a suggestion? Apply a moderate amount of pressure to remove any dust or dirt buildup. Figure : Disconnect the power cord Wait 15 seconds. If your printer is connected to the computer with a USB cable, disconnect the cable from the printer. have a peek here
by R. If the plastic frame is cracked or broken and the cartridge can wobble around, it will usually install without any trouble but when you close the access door the carriage immediately moves back into print-ready position. Press the Cancel button () on the control panel. Solution four: Reset the power module, and then test the power Follow these steps to reset the power module on the power cord, and then test the power on the product.
You can only upload a photo (png, jpg, jpeg) or a video (3gp, 3gpp, mp4, mov, avi, mpg, mpeg, rm). note: If the carriage does not move into the access area, turn the product off and then on again. Solution six: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
First Time Here? Solution three: Match the paper to the paper settings Follow these steps to make sure that the paper loaded into the product matches the paper size and type settings in the print driver. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1410 Check Print Cartridge Flashing The reset is now complete.
This thread isn't solved, unless your answer is that Magic Fairy Elves fixed it when you weren't looking!! Hp Psc 1210 Check Print Cartridge Error Figure : Close door Step 2: Determine which cartridge is the problem Do you have the printer connected to a computer? Press and hold the Cancel button (). http://h30434.www3.hp.com/t5/Inkjet-Printing/hp-psc1315-suddenly-gives-me-a-quot-Check-Print-Cartridge/td-p/1562999 Before loading paper in the tray, hold the stack of paper, and then tap the bottom edge on a flat surface so that the stack is even on all sides.
Reply 0 0 Everyone's Tags: xx View All (1) VisionAiry Distinguished Professor Posts: 3,396 Member Since: 02-15-2013 Message 9 of 18 (8,864 Views) Report Inappropriate Content Re: Sudden Print Cartridge Error For PSC 1315 Unsolvable! How To Reset Hp Psc 1410 Printer The carriage moves to the center of the product. The system returned: (22) Invalid argument The remote host or network may be down. Reconnect the power cord to the rear of the product.
Dip a clean foam rubber swab or lint-free cloth into distilled water, and then squeeze any excess water from it. http://orgias.org/hp-psc/hp-psc-1350xi-check-print-cartridge-error.html Pulling paper from inside the front cover can cause mechanical damage to the product. Brought them home, reinstalled them, and everything worked fine. Reconnect the power cord to the rear of the product. Hp Psc 1210 Troubleshooting
Step two: Test the power on the All-in-One Follow these steps to test the power on the product. It remains a mysterious singular occurrance. If the issue persists, continue to the next solution. Check This Out When only the On/Resume button () is blinking, release both buttons.
Disconnect the USB cable from the rear of the product. Hp Psc 1350 Manual If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. I...
An alignment page prints automatically. Clean the print cartridge contacts. Securely reconnect the USB cable to the rear of the computer. Hp Psc 1350 Error Code E note: If the alignment page fails to print, repeat the button-press sequence in this step.
Figure : The door pins Step three: Clear the paper jam from the front of the All-in-One If you cannot remove the paper jam from the rear of the product, follow these steps to remove the paper jam from the front. If the issue persists, continue to the next solution. Do not hold the button down. http://orgias.org/hp-psc/hp-psc-1210-check-print-cartridge-error.html caution: Do not disconnect the power cord during this step.
Gently lower the tray until it is horizontal and stops. Find Solutions, ask questions, and share advice with other HP product owners. Torn, wrinkled, or damp paper loaded in the paper tray. they both show as a thin line, even though they were recently new/ and refilled.I have tried to -Gently rub the connections with an eraser to remove any marks and with a damp tissue to remove any dried ink on the bottom edge of the cartridge.
Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. I follow the manual procedure. The alignment page prints. Sign in to add this video to a playlist.
Step four: Print a self-test report Follow these steps to print a self-test report. Nothing will print, I can't clear the error, I have tried cleaning them and using all of the options listed under trouble shooting. An alignment page prints automatically. Step three: Replace the USB cable Securely connect an alternate USB cable to the rear of the product.
Once reported, our moderators will be notified and the post will be reviewed. Press the Cancel button () on the control panel. If the lights on the control panel still blink, continue to the next step. Lower the paper tray, and if necessary, slide the paper width guide to its outermost position.
Anyways if it printed in color, shouldn't it be an isolated problem with my black ink cartridge? If the printer is connected to a computer and the HP software has been installed, one of the following messages is displayed: The cover is open The print cartridge on the right side of the carriage is missing, not detected, or incorrectly installed The color print cartridge is missing, not detected, or incorrectly installed Print cartridge error Step 1: Close door If the cartridge access door is open, close it. they will help you in isolating the issue. The reset is now complete.
Not a refill. Figure : Gently remove the jammed paper caution: Use a flashlight to thoroughly check the rollers and wheels for torn pieces of paper that might remain inside the product. Figure : Open the cartridge access door Wait until the product is idle and silent, and then disconnect the power cord from the rear of the product.