Press in the tab on the left side of the door, and then pull the door away from the product to remove it. Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Always try to pull jammed paper from the rear of the product or the paper tray. Do not overload the tray with paper. Dip a swab in the clean water, then squeeze it to remove most of the moisture. have a peek here
Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. If you cannot cancel the task, press and hold the On/Resume button () for three seconds to turn off the product. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 06-07-2012 06:52 PM My HP PSC 1315 was working fine.
Bitte versuche es später erneut. If the new cartridge fails then the news is grim. Open the scanner lid. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.
Figure : Lower the paper tray You might have to press the On/Resume button () again to resume the task. To do a hard reset:1. Experiencing frequent or recurring paper jams? Hp Psc 1210 Troubleshooting If you cannot cancel the task, press and hold the On/Resume button () for three seconds to turn off the product.
The alignment page prints. Hp Psc 1350 Troubleshooting The printer still works great after many years of service. Press and release the Cancel button () again. If the product uses a power module with a detachable power cord, disconnect the cord from the power module.
Figure : HP PSC 1200, 1310, 1340, and 1350 control panel with the lights indicated On/Resume light Check Paper light Check Print Cartridge light Copies display (where an 'E' might display) Black Start Copy light Color Start Copy light note: There might be more than one solution for some blinking lights patterns. How To Reset Hp Psc 1410 Printer If the message on the computer does not identify a particular cartridge (it says only Print cartridge error), follow the steps below to determine which cartridge is causing the problem. The product prints a self-test report. If the product does not turn on automatically, press the On/Resume button () to turn the product back on.
If after trying the task, a blinking light or combination of blinking lights displays on the product control panel, find the pattern you are experiencing in this document, and then follow the steps to resolve the issue. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1350 Check Print Cartridge Do not print on paper with paper clips or staples attached. Hp Psc 1410 Check Print Cartridge Flashing Make sure that the carriage can move freely by gently pushing the carriage to the left and then to the right.
Reconnect the power cord. navigate here If these steps resolved the issue, you do not need to continue troubleshooting. Press and hold the Cancel button (), and then press the Start Copy Color button. Solution two: Cancel and then retry the task Follow these steps to cancel and then retry the current task. Hp Psc 1210 Check Print Cartridge Error
HP psc 1315I have just refilled my black ink cartridge ( I put a new colour one in a short while ago. Hold the cartridge by its sides. Place it in its slot at a slight angle, and then press up and forward until the cartridge snaps into position. Check This Out Can not find a printer icon on my screen?
Follow these steps to perform a partial reset of the product. Hp Psc 1350 Error Code E This is very frustrating for me because I just purchase new set of cartridges again and this problem still remains the same! Reply 0 0 Gogggy Student Posts: 1 Member Since: 06-01-2013 Message 8 of 18 (8,895 Views) Report Inappropriate Content Re: Sudden Print Cartridge Error For PSC 1315 Unsolvable!
If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product. The reset is now complete. If the issue persists, continue to the next solution. Hp Psc 1350 Manual Figure : Close the cartridge access door You might have to press the On/Resume button () again to resume the task.
Open the cartridge access door. Solution two: Load paper Follow these steps to load letter or A4 paper into the product. Step two: Try the task again Press the appropriate button(s) on the product control panel to try the intended task again. http://orgias.org/hp-psc/hp-psc-1315-check-print-cartridge-error.html Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
This video shows how to print a test page Click here to see this video in full screen on YouTube. When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Press the On/Resume button () to turn off the product. If these steps resolved the issue, and the self-test report prints, there is no need to continue troubleshooting.
If the product successfully turns off, press the On/Resume button () to turn on the product, and then press the appropriate button(s) on the product again to perform the intended task. With the power on, disconnect the power cord from the rear of the product. Remove the rear access door.