Figure : Snap the cartridge into place Close the cartridge access door. If you have already installed the cartridges, proceed to the next solution to check cartridge compatibility. I love this printer - and I don't want to have to replace it because I've done something stupid like push the paper in too far. Figure : Disconnect the power cord Wait 15 seconds. http://orgias.org/hp-psc/hp-psc-1300-print-cartridge-error.html
Do not remove the copper-colored strip. If the settings in the Paper/Quality tab are incorrect, change the settings to match the paper loaded in the paper tray. Figure 4: Removing the tape Replace the cartridge. I have tried alot of things and they are not working. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00461967
by unknown on May 17, 2008 at 9:31am Add comment Please sign in to comment In reply to Minnella, this might sound silly, but I had the same problem and simply disconnecting the power plug from the back of the printer and plugging it back in solved the problem. Figure : Gently remove the jammed paper caution: Use a flashlight to thoroughly check the rollers and wheels for torn pieces of paper that might remain inside the product. The product prints a self-test report.
Figure : Disconnect the USB cable from the rear of the product Disconnect the USB cable from the rear of the computer. by GaryCClark on Jan 17, 2011 at 9:56am Add comment Please sign in to comment 0 I have posted before about my 1350 not printing red. Hold the cartridge by its sides. Figure : Open the cartridge access door Remove the new cartridge from its packaging, and then use the pull tab to remove the protective tape from the nozzles. Figure : Remove the protective tape using the pull tab caution: Do not touch the copper-colored electrical contacts or the ink nozzles on the cartridge.
Try the intended task again. Hp Psc 1350 Manual I have the old ones(4 year old cartridges) in the fridge and not the freezer..so is it safe to have those in the fridge? If these steps resolved the issue, you do not need to continue troubleshooting. http://support.hp.com/us-en/document/c00095908 An alignment page prints automatically.
Press the On/Resume button () to turn on the product. Reconnect the power cord to the rear of the product. If the issue persists, continue to the next solution. If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members.
We have had the problem for months now. https://forums.techguy.org/threads/hp-psc-1350-all-in-one-wont-work.739896/ To check the warranty on your ink or toner supplies, go to hp.com/go/learnaboutsupplies, select your country/region, and then review the limited warranty information for your supplies. Hp 1350 Printer Check Print Cartridge Error Use only one type of paper at a time. Hp Psc 1350 Troubleshooting If you have a defective cartridge or printhead, it might be under warranty.
If the product does not turn on automatically, press the On/Resume button () to turn the product back on. navigate here Reconnect the power cord to the rear of the product. I suspect that there is something wrong with the ribbon cable or driver in the printer. Get news about the products and tech you really care about. Hp Psc 1350 Printer
Open the Toolbox and tell it that you have installed new cartridges and re-align. You can swap the cartridges or just take the one not printing red out and dunk the bottom in really hot water and then blot it dry. Was the information on this page helpful? Check This Out On some models, the language and country/region settings also reset.
Show Ignored Content As Seen On Welcome to Tech Support Guy! Please help. See how long it can show the 1once its back up.
Thanks by unknown on Dec 19, 2007 at 6:34pm Add comment Please sign in to comment I've noticed that with only one cartridge installed my PSC 1350 won't print. Torn, wrinkled, or damp paper loaded in the paper tray. note: If the carriage does not move into the access area, turn the product off and then on again. note: You might need a flashlight to illuminate areas for proper viewing.
Damaged or dirty paper rollers. HELP!!! If the message on the computer does not identify a particular cartridge (it says only Print cartridge error), follow the steps below to determine which cartridge is causing the problem. this contact form Close the cartridge access door.
First Time Here? I am trying to print pre printed invites that are a half a portrait page so 5.5 X 8.5. When only the On/Resume button () is blinking, release both buttons. When only the On/Resume button () is blinking, release both buttons.
The icon on the USB cable () generally faces up when the cable is connected correctly. If you can get it to give you that 1 again, try turning it off normally, then turning it back on. by Erskine83 on Jun 15, 2007 at 10:07pm Add comment Please sign in to comment 0 I really need help, i cant print or anything cause every light is flashing and when i turn it off, this HEWLET-PACKARDOFFICEJETFLASH RELFASH thing pops up and it tells me to find updates and stuff wnd when i do, it says it cant find any. Blinking Lights on the HP PSC 1200, 1310, 1340, and 1350 All-in-One Printer Series Blinking Lights The following sections describe all combinations of blinking (flashing) lights displayed on the product control panel, followed by solutions for each combination.
Slow printing - If your PSC printer is printing slowly, resetting it should clear out the excess memory from your printer and make it responsive again. Ink Cartridge Problems - sometime ink cartridge is not being detected by the printer. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Wait 15 seconds.