Let me know if this works for you. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. In the program being printed from, click File, click Print, click Properties, and then click the Paper/Quality tab. Step one: Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. have a peek here
I have done every troubleshooting techniqueon the HP site and in the help files, even cleaning the cartridges, to no avail. Solution six: Clean the cartridges and inside the All-in-One Follow these steps to clean the electrical contacts on the cartridges and inside the product. Check the control panel to make sure that the lights are no longer blinking. If the product successfully turns off, press the On/Resume button () to turn on the product, and then press the appropriate button(s) on the product again to perform the intended task.
Open the cartridge access door. Figure : Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. caution: You must disconnect the power cord to move parts by hand without the risk of an electrical shock. Make sure the HP product supports the paper type.
Follow these steps to determine which cartridge is defective, and then remove and replace that cartridge. If these steps resolved the issue, you do not need to continue troubleshooting. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1410 Check Print Cartridge Flashing Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
If the issue persists, continue to the next solution. Hp Psc 1350 Check Print Cartridge Wird geladen... How does HP install software and gather data? click for more info Solutions Solution one: Wait for the All-in-One to complete the job The product is processing a copying, scanning, printing, or photo or maintenance job.
Figure : Remove the rear access door Press in the tab Pull out the door Gently remove any jammed paper or bits of torn paper from the rollers inside the product. How To Reset Hp Psc 1410 Printer Press in the tab on the left side of the door, and then pull the door away from the product to remove it. Place your index finger in the finger slot on the paper tray at the front of the product. Figure : Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product.
Trying to clear jammed paper from the front of the product can damage the print mechanism. http://h30434.www3.hp.com/t5/Inkjet-Printing/Sudden-Print-Cartridge-Error-For-PSC-1315-Unsolvable/td-p/277223 Right-click the following link, How to Buy HP, to buy a compatible power cord. Hp Psc 1210 Troubleshooting If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1315 Check Printer Cartridge Error Figure 7: Print carriageFigure 8: Clean the gold-colored contacts in the print carriageStep 5: Repeat reseating and cleaning stepsIf the print cartridge light keeps flashing, repeat steps 3 and 4 above.
If this happens, press and quickly release the On/Resume button () again. http://orgias.org/hp-psc/hp-psc-1210-check-print-cartridge-error.html Today scanned about 15 pages without error. Figure : Secure the USB cable note: Make sure that the USB cable is connected correctly. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1350 Troubleshooting
Disconnect the power cord from the rear of the product. Follow the steps in this document for Blinking Lights. Anmelden 5 Wird geladen... http://orgias.org/hp-psc/hp-psc-1410v-check-print-cartridge-error.html Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > Sudden Print Cartridge Error For PSC 1315 Unsolvable!
The sequence must be completed within 10 seconds. Hp Psc 1210 Reset Make sure that the carriage can move freely across the width of the product by gently pushing the carriage to the left and then to the right. Wiedergabeliste Warteschlange __count__/__total__ Printing a Test Page - HP PSC 1200 All-in-One Printer justprintingaround AbonnierenAbonniertAbo beenden3.8493 Tsd.
Reconnect the power cord to the rear of the product. Step one: Remove the cartridges Press the On/Resume button () to turn on the product. Pulling paper from inside the front cover can cause mechanical damage to the product. Reset Hp Psc 1210 All In One Press the Cancel button () on the control panel.
Figure : Slide the paper width guide in against the edge of the paper Press the On/Resume button () to continue the task. To start with.. Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. this contact form Do not overload the tray with paper.
Press and release the Cancel button () again. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Close the cartridge access door. If any torn pieces of paper remain inside the product, more jams are likely to occur.
HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend possible solutions. It might take several tries to complete the sequence within ten seconds. Showing results for Search instead for Do you mean or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous Topic Next Topic » CHazelnut Student Posts: 1 Member Since: 03-06-2016 Message 1 of 2 (87 Views) Report Inappropriate Content HP psc 1210 xi, blinking "Check Print Cartridge" Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 03-06-2016 09:45 PM Product Name: HP psc 1210 xi Operating System: Microsoft Windows 10 (64-bit) Windows 10 installed 6 months ago, no prior problems with printer. Solution nine: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.