Home > Hp Psc > Hp Psc 1210 Print Cartridge Error

Hp Psc 1210 Print Cartridge Error

Contents

If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. If the self-test report does not print, skip to the next step. Continue with the steps below - you must perform the steps on both cartridges.Step 3: Remove and reseat the problem cartridgeIf the problem still occurs, the electrical contact between the cartridges and the printer might be bad. You might also experience the following symptoms: The product will not print. http://orgias.org/hp-psc/hp-psc-1210-all-in-one-check-print-cartridge-error.html

Damaged or dirty paper rollers. When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Connect any other needed cables to the printer.Are you still seeing the error message?Please continue troubleshooting here: Check Print Cartridge Light Blinking ProblemFocus on the cleaning of the cartridges. Solutions Copy, Scan, or Print Press the appropriate button(s) on the product to perform the intended task.

Hp Psc 1350 Check Print Cartridge

note: If you have already installed the front panel overlay, proceed to the next solution. Apply a moderate amount of pressure to remove any dust or dirt buildup. Close the cartridge access door by pressing firmly on the door until it snaps into place. If these steps resolved the issue, you do not need to continue troubleshooting.

HevnLghI work on behalf of HPClick the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping! Figure : The door pins Step three: Clear the paper jam from the front of the All-in-One If you cannot remove the paper jam from the rear of the product, follow these steps to remove the paper jam from the front. Check the control panel to make sure that the lights are no longer blinking. Hp Psc 1210 Troubleshooting Bought new carts.

If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1350 Troubleshooting Then slide the cartridge out of the carriage. Try the intended task again. Ink cartridges dry out over time..

Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Figure : Load the alignment page Close the scanner lid, and then press the Scan button on the control panel. How To Reset Hp Psc 1410 Printer Wait until the On/Resume button () is steady. Pulling paper from inside the front cover can cause mechanical damage to the product. Also, please save your feedback till the end of the process.

Hp Psc 1350 Troubleshooting

Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Always try to pull jammed paper from the rear of the product or the paper tray. Issue: The On/Resume light blinks for 3 seconds and then remains on, and the Black Start Copy and Color Start Copy lights blink In this normal condition, the On/Resume light () blinks faster for three seconds and then stays on. Hp Psc 1350 Check Print Cartridge Trying to clear jammed paper from the front of the product can damage the print mechanism. Hp Psc 1315 Check Printer Cartridge Error If the issue persists, continue to the next solution.

Step one: Reset the power module The power module has a safety feature that protects the product during a power surge. navigate here If the issue persists, continue to the next solution. The color cartridge belongs in the slot on the left. None of the suggested troubleshooting techniques in the user ref manual do any good. Hp Psc 1410 Check Print Cartridge Flashing

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. The icon on the USB cable () generally faces up when the cable is connected correctly. Today scanned about 15 pages without error. http://orgias.org/hp-psc/hp-psc-1210-check-print-cartridge-error.html Unplug the power cord from the wall outlet.

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Hp Psc 1350 Error Code E Make sure to bypass any sort of surge protector or power bar.I would also suggest following through with the steps listed in this document on Print Cartridge Errors.If those do not resolve your issue, I would suggeest contacting HP directly. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

Figure : Open the cartridge access door Remove the new cartridge from its packaging, and then use the pull tab to remove the protective tape from the nozzles. Figure : Remove the protective tape using the pull tab caution: Do not touch the copper-colored electrical contacts or the ink nozzles on the cartridge.

Wait at least 15 seconds. Follow these steps to perform a partial reset of the product. Remove any loose paper or obstructions found. Hp Psc 1350 Manual note: If the page displays in the wrong country/region or language, click the Region - Language link in the upper right corner of your browser.

If these steps resolved the issue, you do not need to continue troubleshooting. Do not use too much paper. If these steps resolved the issue, you do not need to continue troubleshooting. http://orgias.org/hp-psc/hp-psc-1210-error-check-print-cartridge.html If the power module does not have an LED, continue to the next step.

Replace your cartridges, and you wont have this error anymore.. Try the intended task again. Check the lights on the control panel to make sure that they are no longer blinking. If you experienced a recent power surge, the power module might need to be reset.

On some models, the language and country/region settings also reset. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. Within the last year? The rear access door might not be closed or is not locked into place.

Press and hold the Cancel button (), and then press the Start Copy Color button. Plug the power cord back into a wall outlet. An alignment page prints automatically. Wait until the On/Resume button () is steady.

Your cartridges need to be replaced.. If these steps resolved the issue, you do not need to continue troubleshooting. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. Load plain, white paper into the paper tray.

If the LED does not light up, contact HP to replace the power module. This video shows how to clear a paper jam from the All-in-One Click here to see this video in full screen on YouTube. If these steps resolved the issue, you do not need to continue troubleshooting. Follow these steps to perform a partial reset of the product.

Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray. Figure : The door pins Reconnect the power cord to the rear of the product. Step three: Search for more information If you are still experiencing issues, see the HP Product Support Home Page, and then search for another document that relates to the symptoms you are experiencing.