Press the On/Resume button () to turn on the product. Step one: Perform a power reset Press the On/Resume button () to turn on the product. Post a reply Discussion is locked Flag Permalink You are posting a reply to: HP psc 1200 The posting of advertisements, profanity, or personal attacks is prohibited. BTW, I cannot be responsible for detailed directions and a guarantee to make this work. have a peek here
Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Always try to pull jammed paper from the rear of the product or the paper tray. Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. Make sure the HP product supports the paper type. Click on the Advanced tab. http://www.neowin.net/forum/topic/449372-hp-psc-1200-series-system-error-solution/
We have not detected any issues with your product. You may find a relevant support option by selecting any of the helpful topic tabs on this page or by entering your issue in the above search tool. Press the On/Resume button () to turn on the product. Press and hold the Cancel button (), and then press the Start Copy Color button. Do not use paper that is too thin, too thick, or too glossy for the product.
The carriage moves to the center of the product. by unknown on Mar 5, 2009 at 3:14pm Add comment Please sign in to comment 0 IF THIS DOES NOT WORK FOR YOU TRY THE DEP PROCEDURE AGAIN BUT ADD ALL VERSIONS OF C:\\WINDOWS\\system32\\spool\\drivers\\w32x86\\3\\hpzeng07.exe SOME ARE IN OTHER FOLDERS OF THE w32x86 directory.I hope this helps - It just helped meGraham by unknown on Apr 20, 2009 at 2:41pm Add comment Please sign in to comment 0 OHH thanks a millions for solving this problem. If the LED lights up, continue to the next step. Hp Psc 1200 Driver Windows 7 64 Bit Download If the product completes the job normally, there is no need to continue troubleshooting.
If you email me at [email protected] I will be glad to send you the EZinstall file. Hp 1350 Printer Check Print Cartridge Error Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. In short, what you need is a file called EZinstall that you run with your HP software disk in your CD drive. http://support.hp.com/us-en/document/c00095908 If the issue persists, continue to the next solution.
The alignment page prints. Hp Psc 1200 Printer Offline Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. by glb613 / May 25, 2005 8:23 PM PDT In reply to: HP 3 in 1 They only way to copy is to scan the document. Pulling paper from inside the front cover can cause mechanical damage to the product.
It works on hp psc 1110 too. Figure : Disconnect the power cord Wait 15 seconds. Hp Psc 1200 Driver If the issue persists, continue to the next solution. Hp Psc 1210 Driver Download When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time.
The paper is jammed inside the HP product where you cannot see it. navigate here Reconnect the power cord to the rear of the product. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. But I can't get the scanner to work. Hp Psc 1200 Driver Windows 7
The E is a general indicator that the printer has experienced an error. Figure : Open the cartridge access door Wait until the product is idle and silent, and then disconnect the power cord from the rear of the product. If the product does not scan, follow the same steps and try a different wall outlet. Check This Out If the power module does not have an LED, continue to the next step.
Solution three: Check cartridge compatibility Visit HP SureSupply to check ink or toner cartridge compatibility, or purchase replacement cartridges. Hp Psc 1210 Check Print Cartridge Error Figure : Check the electrical connections Press the On/Resume button () to turn on the product. I had the same error with a HP PSC 1210 All-in-One series.
If the product successfully turns off, press the On/Resume button () to turn on the product, and then press the appropriate button(s) on the product again to perform the intended task. The reset is now complete. The reset is now complete. Hp Psc 1200 Series Windows 7 Use the scan button on the machine?
Step one: Reset the power module The power module has a safety feature that protects the product during a power surge. The presence of an E, however, does not affect the meaning of the blinking lights, and can be disregarded for troubleshooting purposes. Although not particularly technical, I can do the basics (as I think of them), like installing, updating drivers, etc. this contact form Figure : The rollers in the rear access door Gently push the pins on the right end of the rear access door into the holes on the right side of the rear access area, and then snap the door firmly back into place.
Look inside the product to see where the carriage is stuck, and then check for any torn paper or objects that might be restricting the carriage. Figure : Open the cartridge access door Remove the black cartridge by pressing lightly on the top of the cartridge to release it from its slot. Press the On/Resume button () to turn on the product. Issue: The On/Resume and Color Start Copy lights blink In this normal condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Off Check Print Cartridge light: Off Black Start Copy light: On Color Start Copy light: Blinking Figure : The On/Resume and Color Start Copy lights are blinking Cause The product is busy processing a color print job.
First Time Here? Figure : Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. Close the cartridge access door. When only the On/Resume button () is blinking, release both buttons.
The paper is jammed inside the HP product where you cannot see it. If the issue persists, continue to the next solution. Windows 2000 and XP: Select the Hardware tab, and then click Device Manager. note: Turn on the computer to see the status message for more details.
Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. Preview post Submit post Cancel post You are reporting the following post: HP psc 1200 This post has been flagged and will be reviewed by our staff. If the product successfully turns off, press the On/Resume button () to turn on the product, and then press the appropriate button(s) on the product again to perform the intended task. Press the On/Resume button () to turn on the product.