Home > Hp Psc > Hp Psc 1200 Series Error

Hp Psc 1200 Series Error

Contents

If the issue persists, continue to the next solution. Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Never pull jammed paper from the front of the product. Use only one type of paper at a time. To buy a compatible power module, right-click the following link, How to Buy HP, and then click Open in New Window. have a peek here

Step one: Clean the electrical contacts on the cartridges and inside the product Gather the following materials: Dry foam rubber swabs, a lint-free cloth, or any soft material that will not come apart or leave fibers (coffee filters work well) Distilled, filtered, or bottled water (tap water might contain contaminants that can damage the cartridges) caution: Do not use platen cleaners or alcohol to clean the cartridge contacts. I can find no good reason for this issue. Press and hold the Cancel button (), and then press the Start Copy Color button. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. you could check here

Hp 1350 Printer Check Print Cartridge Error

Do not leave a cartridge outside the product for more than 30 minutes. Follow these steps to perform a partial reset of the product. You just saved me money on a new printer!!

Step two: Reinstall the cartridges To reinsert, hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly upward angle. If these steps resolved the issue, you do not need to continue troubleshooting. Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Figure : Load the alignment page Close the scanner lid, and then press the Scan button on the control panel. Hp Psc 1350 Manual This happened with a cartridge that is about 2 weeks old.

Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Hp Psc 1210 Check Print Cartridge Error Reconnect the power cord to the rear of the product. If your printer is connected to the computer with a USB cable, disconnect the cable from the printer. great post to read Check the control panel to make sure that the lights are no longer blinking.

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. How To Reset Hp Psc 1410 Printer First Time Here? When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Press the cloth against the paper feed rollers, and then rotate them upwards with your fingers.

Hp Psc 1210 Check Print Cartridge Error

Wait until the On/Resume button () is steady. check my blog Press the Cancel button () on the control panel. Hp 1350 Printer Check Print Cartridge Error If the product does not complete the cartridge alignment, it will print an alignment page every time you turn it on. Hp Psc 1210 Troubleshooting Figure : Install the front panel overlay Figure : Correctly installed front panel overlay Reconnect the power cord to the rear of the product.

Securely reconnect the USB cable to the rear of the product. navigate here Solution three: Match the paper to the paper settings Follow these steps to make sure that the paper loaded into the product matches the paper size and type settings in the print driver. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. Wait until the On/Resume button () is steady. Hp Psc 1315 Check Printer Cartridge Error

note: HP supports USB cables less than 3 meters (9 feet 10 inches) in length. Tighten the screws. note: If you have already installed the front panel overlay, proceed to the next solution. Check This Out Hp 56 Check Print Cartridge Reply 0 0 Everyone's Tags: AS1 View All (1) « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10 Upgrade, Printer Does Not PrintHP Printers - Using Google Cloud Print with Your HP PrinterHP Printers - Printer is Offline (Windows)HP Printers - Resolving Printhead Problems and Ink System Failure Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP.

The system returned: (22) Invalid argument The remote host or network may be down. Hp Psc 1210 Reset Check the control panel to make sure that the lights are no longer blinking. If these steps resolved the issue, you do not need to continue troubleshooting.

When only the On/Resume button () is blinking, release both buttons.

Hi,Welcome to JustAnswer! Figure : HP PSC 1200, 1310, 1340, and 1350 control panel with the lights indicated On/Resume light Check Paper light Check Print Cartridge light Copies display (where an 'E' might display) Black Start Copy light Color Start Copy light note: There might be more than one solution for some blinking lights patterns. This page requires Javascript. Hp Psc 1350 Troubleshooting Wait 15 seconds.

If the issue persists, continue to the next solution. We had unplugged the printer before, but not unplugged from the printer, but from the electrical wall. I1- Re installed Printer Drivers2- Re installed "2" NEW sets of print cartridges3- Using contact cleaner I carefully cleaned all the contacts on both the cartridges and the printer as well making sure to let it dry completely for12 hours before reinstalling carts. http://orgias.org/hp-psc/hp-psc-1200-error-codes.html and hooking back up to computer4 - I repeated steps 1 + 2 after I cleaned all the contacts and let completely dry.5 - Finally I took the printer and installed it onto a different machine.

Sign in Share More Report Need to report the video? Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray. If the product successfully turns off, press the On/Resume button () to turn on the product, and then press the appropriate button(s) on the product again to perform the intended task. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

Modify your browser's settings to allow Javascript to execute. Reconnect the power cord to the rear of the product. Do not use paper that is too thin, too thick, or too glossy for the product. Solutions Solution one: Wait for the All-in-One to complete the job The product is processing a copying, scanning, printing, or photo or maintenance job.

The steps on cleaning the cartridge contacts may be helpful. Press and hold the Cancel button (), and then press the Start Copy Color button. note: The black cartridge belongs in the slot on the right. The alignment page prints.

Press the On/Resume button () to turn on the product. The first time I pushed the ‘button' it clicked softly like something dropping back into place… but that didn't make a difference. The product aligns the cartridges. Disconnect the product cord from any power strip or surge suppressor, and then plug it directly into a three-prong wall outlet.

Wait at least 15 seconds. Press the Cancel button () on the control panel. If the issue persists, continue to the next solution. If you cannot cancel the task, press and hold the On/Resume button () for three seconds to turn off the product.