Home > Hp Printer > Hp Printer Error Code 49.ff04

Hp Printer Error Code 49.ff04

If the job prints, go back tothe first application and try printing a different file. Try reseating the formatter and all components attached to the formatter. Attempt to print the Configuration page from the control panel. We don't provide a link because HP keep moving things but a string to search for might be HP LaserJet and OfficeJet Enterprise - Latest Firmware Versions and at the time of writing the firmware id is 20141230 04.221.6. http://orgias.org/hp-printer/hp-printer-error-49-ff04.html

by unknown on May 3, 2012 at 3:46pm Add comment Please sign in to comment 0 Hi,I'm getting the same error on a HP P3015, which already has the latest firmware installed.The printer is attached over the network.What could be the problem? If the formatter light is not blinking, proceed to Step 2. A stack trace won't tell you (or us) much because we don't have the source code. Maybe it is adriverissue.

Once the printer is back online, print a Configuration Page and verify that the new firmware has been installed. If it can do the job then that suggests recent printer firmware is to blame. Could the error be with my network or the printers?After a while the error clears its self.Please HelpMoses by unknown on May 17, 2011 at 2:13am Add comment Please sign in to comment You might want to try looking into one of the network hubs on your network....Your issue sounds like what I had gone through...and I did resolve my issue.One of your hub may have a shared network port....usually labeled as the.. "uplink" port and it is usually shared with the last port on the hub...This special port is a shared port for the network and cannot be both in use at the same.

The scanning computer might not have enough available resources. Very occasionally we will turn a problem that can be resolved with a firmware update, but it's a rare case. Some of these formatters were shipped with the Toshiba NAND flash chip which seems to fail. Fortunately they had a replacement and the difference was immediate.Besides the 49 error, their printer started pausing 2-3 seconds between printing when it would print.

If a weird service hits this port and starts sending non-ascii hex, the printer will interpret it as best as it can unless it runs into and opcode(hex byte) it can't understand.Start with firmware and drivers. Right-click the printer you need to send the upgrade to, then choose Sharing… 3. There were three more clueless results before Google said repeat the search with the omitted results included. http://www.fixyourownprinter.com/posts/39866 For example: “HP LaserJet mfp” 2.

First thing you will want to do is a firmware upgrade to prevent it from happening again. Is there any additional info that someone has that has not been published by unknown on Dec 7, 2010 at 12:32pm Add comment Please sign in to comment 0 Since it's network related, update the embedded jetdirects firmware along with the printer firmware. Removal of theformatterand running of anenginetest, usually a line test pattern will help you to eliminate theformatteras a possible cause of failure. This error generally shows up when printing pdf documents however can occur simply from a communication issue between the printer and the computer.

The simple solution for us was to turn off the RAM disk on the printer. Read More Here What HP generally want for a "49" error is a stack trace - but they might be losing interest in the P4014 series since it was new in 2008. It may go away for a few days but comes back. If you get the infamouse 49.4C02, this could be the job or firmware TYPICALLY.

If the message persists with different applications and print jobs , disconnect all cables to the printer that connect it to thenetworkor PC. navigate here Press the Down arrow until you see "Set RFU Error Off". Doing that changes nothing. - tried disconnecting ethernet cable. by moe on Jan 24, 2012 at 3:49pm Add comment Please sign in to comment 0 I avoid using an oven for a few reasons.

Loading... The problem seems to be with theKerberosAuthentication feature. RE: 49 FF04 Service error on HP 4350n hpwizzard (IS/IT--Management) 18 Aug 06 08:31 Most 49.XXXX errors are related to processing job issues or communication problems. http://orgias.org/hp-printer/hp-printer-error-code-41-8.html Firm ware error issue.If printer comin to ready mode try to up load form ware, no ready mode replace formatter Question about HP LaserJet Printers & Copiers 2 Answers HP Laserjet 2420dn will not print and is ...49.FF04 service error' Does the error display when printing a particular job, or anything that you print?

The number given after 49 is an identifier, address of the crash (or possibly the crash handler trap). Repeat for each EIO device. They go for $80ish if you find the right model.

because they can fail and leave error messages like this.

Covered by US Patent. We are using a Novell network with Cisco switchs, any suggestions on what I could check on the network, This is only happening with the 4250N printers, we also use 5si, 8000, 8250, 4000, 4100, &5500 printers.Thanks - Anonymous 0 Novell network means you are probably using a print server. Test any EIO devices, by turning off the printer, installing each device separately, and printing a Configuration page. Illustrates the problem with forums (fora?).

Next, turn the printer off and back on. Turned off the RAMDISC as suggested above and it seems to have worked. NVRAMinitialization: CAUTION: InitializingNVRAMresets the serial number, the event log, the page counts, the calibration settings, and theEIOcard. http://orgias.org/hp-printer/hp-printer-error-code-52-00.html Also keep in mind that if the 4250/4350 series power is derived from the lvps and not the dc controller.

by akuma6099 on Dec 3, 2010 at 11:01am Add comment Please sign in to comment 0 I am having the 49.FF04 error on 30 or so 4014 and 4015 models.We are installing new printers in locations that had older HP 4000 models which worked with no problems. Is it at the pickup/feed area, transport area (under the drum),fuseror the exit area? This type of error can be caused by invalid print commands, corrupt data, or invalid operations. Also firmware updates can be a bit complicated and the file transfer can fail; so we don't recommend you do firmware updates unless necessary.

NOTE: As mentioned earlier some solutions and accessories may not be 100% compatible with a newer version of HP firmware. Please try again later. On your computer go into the printq and delete all pending print jobs and it should now work. Prev12Next » Not finding what you are looking for?

Press the Checkmark button, then press the Menu button. If it won't clear ... If the error continues with accessories removed from the formatter, perform a cold reset on the printer.