Home > Hp Printer > Hp Printer Error 80.x

Hp Printer Error 80.x

Check/replace SIMMs. 62.x memory error 4000/4050/4100/5000/8000/8100 only: 62.x where x = Dimm slot, Check/replace DIMMs. 63 SERVICE 1. At least one of two tabs must be present. 3. Replace the EIO accessory in slot [z]. Figure 7: Reinstalling the print cartridge and closing the top cover If a jam message persists, there is still jammed paper in the printer. have a peek here

The product was delivered just a few minutes ago. Replace appropriate fan as needed. Reply 0 0 FredHD1 Honor Student Posts: 2 Member Since: ‎06-11-2016 Message 5 of 9 (626 Views) Report Inappropriate Content Re: error code OXB80AF934 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎06-11-2016 09:10 AM Hi,having the same issue here, very disapointed by this connexion.Have you had a chance to have it fixed meanwhile? The printer door/lid is open. 2. http://www.all-laser.com/aerror-code/

The EIO accessory card has encountered a critical error.2. Back Error 12 Printer Open Paper path door (IIP/IIIP) or top cover open. Out of spec media. 3. Error 30 PS Error XX ALL PRINTERS PCL file was sent to the printer while in PostScript mode or the PostScript file contains bad data, or you have experienced and application error (crash).

Check the configuration of the EIO (HP Jetdirect card) and the host computer. Is the software set for the size you're using? Turn the printer power off and then turn the printer power on. First Time Here?

You can verify this by substituting a known good DC controller if possible. Try printing a job from a different software application. ERROR 49.XXXX A critical firmware error has occurred that caused the processor on the formatter to abort the operation. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 All Rights Reserved.

You might damage the fuser. IIISi/4Si Only: 1. Replace Laser Diode Assembly. 3. Check and reinstall.

To exit the Help system, press (Help) again. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/error-code-80-01/td-p/5433302 If loose toner falls into the printer, it might cause temporary problems with print quality. They change as the state of the printer changes. I/O card is unable to accept data or is not connected to the network. 30 PS ERROR XX 1.

Figure 54: Removing the tray Pinch the release that is located on the left guide and slide the side guides to the correct paper size. navigate here X description: 0 = The duplex mechanism has failed 1. Figure 10: Checking the quality of the inserted paper Slide the tray back into the printer. There is nothing wrong with the WIFI or computer internet connection.I would appreciate any help.

Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. Check for opens on the cable. Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. Check This Out top 20 INSUFFICIENT MEMORY For help press ?

Action Remove the printer from any UPS supplies, additional power supplies, or power strips. If the error persists, replace the HP Jetdirect card (EIO card). Turn the printer off, and then turn the printer on. 3.

Action Check for a loose cable connection and make sure to use a high-quality cable.

Error 79 Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Error 57 6P/5P/5 Main motor problem, check gear train for binding. Reset inteface cable 3. Back back to top How did we do?

Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. Plunger missing on top cover. 2. HP LASER PRINTER 9000, 9040, 9050MFP 1. this contact form To view Help for a message (if available), press (Help).

Check tabs on side of toner cartridge. If paper is present, remove it. The part of the top door that pushes the Plunger down is broken. 13 PAPER JAM 2686 Only: 1. Action NOTE: Press the ? (help) button for detailed information about clearing the jam.

Replace DC Controller PCA. 3. Sometimes you can clean a pickup roller and get a little more life miles out of them but when you start to get jams with a smudge on the top middle of the page, it's time to replace the roller. If the problem persists, contact HP Customer Support. top 10.XX.YY SUPPLIES MEMORY ERROR Description The printer is unable to read the electronic information (e-label) on the print cartridge so that the printer can keep track of the page count for the print cartridge.

On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. Was the information on this page helpful? top 41.X PRINTER ERROR For help press ? Pull gently on the bin to make sure that the hinge pins are fully inserted.

Disconnect all optional paper handling accessories and try printing again. top 13.XX.YY JAM Description A paper jam exists in the paper path. IIP Only: 1. Turn the power off.

Printing can continue, but behave unexpected in response to the changed settings. If the above action does not solve the issue, reload the tray with the correct paper size. If you are printing from Tray 1, verify that the correct paper size is selected at the printer control panel. Remove the duplexer if installed.