Thanks-Robert by rhipwell on May 14, 2008 at 8:17am Add comment Please sign in to comment 0 I had a similar problem a while back. You guys made my day :) - Anonymous 0 Magnetism has absolutely nothing to do with it. Print and audit the setup page. Press ITEM until PRINT PAPER PATH TEST shows up in the printer show. have a peek here
You saved us a multi-hundred dollar service call. by Smithjohn on Jul 5, 2012 at 7:35am Add comment Please sign in to comment 0 I know this thread has been going on for a very long time but....I only get a Media Feed Error, 41.5, when printing using the duplexer. I dont feel that the laserscanner/ECU is going to resolve this issue as the MP tray works fine. All you need to do is clean off the "L" arm and put a small piece of electrical tape where the glue was and put everything back together.
Thanks for the info. We provide LaserJet 4200/4300 printer repair with 13.01.00 paper jam service error Quick on-site LaserJet 4240, 4250, 4300, 4350 printer repair with 13.01.00 paper jam error indicates that the media did not arrive at the pre-feed sensor (ps102) within the specified time. Press SELECT to perform the paper way test. P/N= RG5-2651-090CN It has an electric motor/clutch on the end that was not working properly.
Feel the resistance of the clutch by turning it by hand. by unknown on Jan 16, 2008 at 11:04am Add comment Please sign in to comment I have a similar problem here. Today i got this same prblm and i dunno what happen, i've checked almost everything still same prblm. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. 10.
Press roller down for easy removal. O reparo girado para fora para ser muito fácil mas se eu não o figurar para fora pode ter resultado em um atendimento técnico caro.Meu rolo da separação - o rolo azul & cinzento na bandeja de papel - tinha-se movido fora do lugar. Replace the Ink Cartridges. On the off chance that a HP Jetdirect printer server EIO card is introduced, a HP Jetdirect setup page will print out also.
To uproot the food roller, squeeze the discharge at the left half of the roller and slide it off the pole. by dmzcompute on Jan 5, 2009 at 4:58pm Add comment Please sign in to comment 0 found this thread via Google while trying to resolve a 41.5 code on my 4050N...in my case, I was trying to print envelopes or narrow cards using manual feed and the adjustable guide on Tray 1. No part of this site, or its source code, may be reproduced in any way. by Anonymous on Feb 8, 2007 at 7:46am Add comment Please sign in to comment 0 Where is the clutch located on the HP laserjet 4000?
Your help was a blessing. :) by unknown on Oct 13, 2010 at 4:50am Add comment Please sign in to comment 0 aardvarknine.
i tried changing the driver to see but no dice. NOTE: A setup page can be utilized to view printer settings and figure out what choices are introduced on the printer. In the event that not able to print an occasion log, design page or menu map from a lower tray(s), endeavor to print with Tray 1 set to First .
HP laserjet 4050 printer repair 90014 Downtown L.A. navigate here I hope that this post helps someone else in the future with a persistant 41.5. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? If there is no glue, why would it stick?Thanks again - it is nice to see a familiar name (you helped me get fusers to repair printers in the past). - hskanner 0 Tray 1 is a separation pad issue.
You can change this preference below. Wird geladen... Too fast or too slow a time will show this error. Check This Out NOTE: Paper movement from lower trays and roller turn may be seen from the once more of the printer.
by Bill on Nov 30, 2004 at 9:09am Add comment Please sign in to comment Bill,Thanks for the info. I noticed that the 4200 have a nonmagnetic, spring based clutch. If the job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or print job, contact the software vendor for assistance.) 4.
Review trays for fitting paper stacking. Turn the tray over and you will see the spring. It was the roller on tray 2 that had shifted to the left, fixed by moving it back into place.Again, thanks. The original posting worked for my issue and I was just happy I found it & it worked & wanted to thank the person who posted it. - unknown 0 I was responding to the post by Raymond above and did not realize it was back in July.
Seems the clutch on the assembly will sometimes fail to engage, causing a 41.5Part # RG5-2651-090CNBagger by Bagger on Aug 12, 2005 at 8:23am Add comment Please sign in to comment 0 Hi bagger. reconditioned pick D rolls on both T2 assembliesAt this point I am unsure what else to do - MP tray works fine.When printing from T2 I get a blank page half out of the top output assy before the unit stops with a 41.5/13.2 error. One of the more common error codes in the HP laserjet 4000, 4050, 4100 as they age is the 41.5 printer error. this contact form Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus!
Learn more You're viewing YouTube in German. Didn't have to hire this one out - sorry!