Home > Hp Printer > Hp Printer Error 41.2

Hp Printer Error 41.2

Verify standard/custom switch setting. 2. You can do a forum search on 3005 and get an idea of how bad it is. Reply 0 0 Harlandts1252 Top Student Posts: 3 Member Since: ‎02-18-2016 Message 7 of 7 (349 Views) Report Inappropriate Content Re: Hp p3015 error 41.20 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎02-26-2016 06:52 AM I have since replaced the prTR and disposed of the defective one. Finally, it is possible, although unlikely, that a bad laser scanner or DC Controller could cause a 41.2 error. have a peek here

Just a quick confirmation - you mean that blue/green colored sleeve on the roller that you can see from the back of the printer? Press GO. Replace the formatter.5. If the error persists, reseat the connections to the laser/scanner, formatter, and engine controller.3. try this

Replace the D.C. HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 41.X 1. Privacy Policy Terms of Use Hp Error Code 41, Service Errors 41, Laser Printer Repair Fuser HP LASER PRINTER ERROR CODE 41 - TEMPORARY PRINT ENGINE FAILURE / 41.1, 41.2,41.3 UNEXPECTED PAPER SIZE/ 41.4, 41.5 UNEXPECTED PAPER TYPE ALL HP LASER PRINTERS ERROR CODE 41 1. Replace paper tray Pulls more than one sheet of paper.

Reload the tray with correct media size. 2. Configured the driver with the printer paper type settings.3. Make sure tray is loaded properly. 3. However, a poor connection can cause arcing.

Verify the paper guides are set correctly.3. Power cycle the printer4.Replace formatter and D.C. Is that the fuser assembly? http://www.advancedlaser-hp-error-codes.com/error_41.htm caused by "Cheap Cartridge".

Reset unit / Cycle power 4. Turn the printer off and then on the clear the error codes.HP LASER PRINTER 8100,8150 ERROR 41.1, 41.2, 41.4, 41.5, 41.91. Replace the engine controller board HP LASER PRINTERS 1200, 2200, 3100 FAX, 3200 FAX, 4100 1. Reload the paper in the tray and make sure the length adjustment is set correctly.3.

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous Topic Next Topic » Harlandts1252 Top Student Posts: 3 Member Since: ‎02-18-2016 Message 1 of 7 (452 Views) Report Inappropriate Content Hp p3015 error 41.20 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎02-18-2016 01:41 PM Product Name: Laserjet P3015 Error 41.02.00 Solved! http://h30434.www3.hp.com/t5/LaserJet-Printing/Hp-p3015-error-41-20/td-p/5505470 The most common cause of arcing is a bad connection to the transfer roller. Verify that all paper size settings on thecontrol panel, in the print driver settings,and in the software program match Reply 0 0 Harlandts1252 Top Student Posts: 3 Member Since: ‎02-18-2016 Message 3 of 7 (426 Views) Report Inappropriate Content Re: Hp p3015 error 41.20 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎02-18-2016 09:23 PM None of the above apply. Yhteystiedot Maatalous-metstieteellisen tiedekunnan laitekeskus PL 27 00014 Helsingin yliopisto Kyntiosoite: Latokartanonkaari 7 Toimisto: 02941 58094 Puhelin: 02941 911 (vaihde) Tiedekunta Hp LaserJet virhekoodit ja niiden selvitys 41.1, 41.2, 41.3 UNEXPECTED PAPER SIZE ALL • Defective connections • Laser scanner connections or bad laser scanner assembly • Paper multi feed or wrong size paper • Paper size selection does not match installed paper • One of the cassettes is overfull or improperly adjusted • Paper is out of spec • Paper pickup and feed rollers are worn, replace rollers • Replace paper input unit • Printer pulls more than one sheet through - worn feed and separation rollers HP 1100, 1200, 2200, 3100, 3200, 4000, 4050, 4100 • Reload the tray with correct media size • Make sure paper tray is loaded properly • Check sensors for proper operation • Worn feed and separation rollers • Make sure the length guide, width guide and size selector switch on the paper tray have been set correctly and be sure that paper is under the front paper tabs • Check the control panel setting for the paper size is correctly configured HP 2300 ERROR 41.3 • Unexpected paper size in tray • Reload the tray with the correct media size • Reconfigure the size in a tray so that contains the size required for the print job • Typically caused if two or more sheets stick together when feeding • Change pick up rollers and separation pad • Replace the engine controller board HP 4200, 4300 ERROR 41.3 • The media that is loaded is longer or shorter in the feed direction that the size that is configured for the paper tray • Print the configuration page and verify that the tray settings match the media in the tray • Check the paper path sensor flags can move freely • Worn feed and separation rollers • Bad DC controller board HP 5000, 8000 • Reload the tray with correct media size • Make sure paper tray is loaded properly • Check sensors for proper operation • Worn feed and separation rollers • Make sure the length guide, width guide and size selector switch on the paper tray have been correctly.

The left connector is a copper leaf spring that directly contacts the metal shaft of the transfer roller. navigate here Sign Up Login Add Question Jay asked May 12, 2004 at 9:59am 0 HP LaserJet 8150 41.2 error HP8150 Im getting a 41.2 error on 2 HP 8150 laserjet printers. Would spew out blank pages and would flash the 41.2 error on the screen. Error 41.2 - Beam detect misprint error.2.

Do I get a new transfer roller - that was the solution to the print quality problems, but will this help the 41.2 error?Or is there something else? Reseat the cables between the laser scanner and the engine control board. What's worse is that HP doesn't seem to care. Check This Out but the error persisted.Help before i throw it out the window.

ie. HP LASER PRINTER 5P, 6P 1. Replace the upper cable guide ass'y4.

I've tried to clean up the NVRAM (no harddisk installed), but message is still there.

Make sure the printer settings in the tray's are the same as control panel and driver.3. I have changed the fuser,toner,rollers,dc controller, and the entire laser/scanner assembly.I also did a full maint. CONTINUE READING Suggested Solutions Title # Comments Views Activity Acrobat Printing Issues 5 52 89d Label Printer and Software 8 69 118d Toshiba E-Studio 2830C Network Copier Scan to E-Mail quit working after DC removal 15 55 51d Printer ink cartridge issue? 22 50 40d The SSPORT Service Failed to Start Article by: djMundy This seems to be a very common error related to the Samsung printer driver. Press the OK button to see if the pagewill print.

Worn feed and separation rollers5. If the paper stickstogether, the paper defect sensors willdetect a sheet of paper longer than whatis expected in the product.4. Check the paper path sensor flags can move freely.4. this contact form However, a poor connection can cause arcing.

Error 41.7 - Feed delay error.5. It will get they error after printing about 20 pages pause then print another 20 pages. Right Connection: The Coil Spring The right connector is a coil spring that connects high voltage through to the right end of the transfer roller shaft. Another thing is to look up doing a nvram reset on the unit and that may clear it up.

Make sure that paper is under the front paper tabs.6. How can I clear the message/error ? Left Connection: The Leaf Spring There are two electrical connections to the transfer roller, one on each end, and both are easily damaged. Replace Fuser.

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Display and Touch  Notebook Hardware and Upgrade Questions  Notebook Software and How To Questions  Business Notebooks  Printers sprocket  Inkjet Printing  LaserJet Printing  Printer Software and Drivers  DesignJet, Large Format Printers and Digital Press  HP Connected, Mobile Printing and Cloud Printing  Scanning, Faxing, and Copying  JetAdvantage, Printing Applications and Services  Desktops Desktop Operating Systems and Recovery  Desktop Boot and Lockup  Desktop Wireless and Networking  Desktop Audio  Desktop Video, Display and Touch  Desktop Hardware and Upgrade Questions  Desktop Software and How To Questions  Sprout by HP  Business PCs, Workstations and Point of Sale Systems  Gaming Gaming Notebooks  Gaming Desktops  Gaming Accessories  Tablets and Mobile Devices Elite x3  Android  Windows  Calculators  Palm and WebOS  Software HP Workspace  HP Touchpoint Manager  HP Collaboration  Commercial PC Software  Archived Topics (Read Only) Notebooks Archive (Read Only)  Printers Archive (Read Only)  Desktops Archive (Read Only)  Tablets and Mobile Devices Archive (Read Only)  Software Archive (Ready Only)  Windows Beta and Previews Archive (Read Only)  Miscellaneous Topics (Read Only)  Your Voice Forum Feedback & Suggestions  HP Expert Portal Welcome to the HP Expert Program  Meet the Experts  News and Events  Blogs Open Menu Blogs Open Menu Best of the Community BlogMeet the ExpertsNews and EventsWelcome to the HP Expert Program Beware of fake HP Support Open Menu Beware of fake HP Support Open Menu Be alert for scammers who may be posing as HP representatives and only call numbers from people who have a label next to their screen name. by rfalb on Dec 3, 2008 at 11:58am Add comment Please sign in to comment 0 I replaced the toner and that resloved the issue. Note that the printer should be able to function without the leaf spring, which is apparently a ground. When … MS Office Office / Productivity Office 365 MS Word Outlook Rename and move Database and log to new volume in Exchange 2013/2016 Video by: acox65807 This video discusses moving either the default database or any database to a new volume.

by dmzcompute on May 12, 2004 at 2:37pm Add comment Please sign in to comment 0 Hi Jay,Have you got any solution to your problem ?I am also experiencing it with my HP 8150 printers. Try that first especially sense it's the eaisest fix. I realize you are a user with few words, but we do need more informaiton starting with when you turn on the printer to when the error appears on the display. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.

Thanks, ":0) Asta 0 LVL 4 Overall: Level 4 Printers and Scanners 3 Message Expert Comment by:mrfixitpc2004-02-09 Your Question needs to be awarded points and closed, Please be fair to all who may have helped in Anyways.