Home > Hp Officejet > Hp Officejet Pro K5400 Error Printing

Hp Officejet Pro K5400 Error Printing

Contents

All lights except the Power light should go off. Check your product warranty to determine if your product is still under warranty, and then go to Contact HP Support to schedule a repair or replacement. Figure 45: Open the top cover If the carriage does not move to the left automatically, press and hold the Resume button () until the printheads stop at the left side of the product. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. have a peek here

Open the cartridge door. Wird verarbeitet... Solution four: Service the printer If you have completed all the steps listed above and are still experiencing a problem, continue to the Service the printer section at the end of this document. Step two: Replace the cartridge Follow these steps to replace the cartridge indicated by the blinking light on the product control panel. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00845054

Hp Officejet Pro K5400 Clean Print Heads

Remove the rear access door. Press and hold the Power button. Important: Before you begin, make sure that the cartridges are compatible with your product.

Go to Contact HP Support to review available service options. Close the cartridge door. Solution one: Clear the paper jam Follow these steps to clear a paper jam. Hp K5400 Clean Print Heads Figure 1: Lights and buttons on the product control panel 1 - Print Cartridge lights 2 - Printhead lights 3 - Configuration Page button (available on some models) 4 - Cancel button 5 - Resume light 6 - Power light The following sections describe the most common combinations of blinking lights, followed by solutions for each combination.

If both Printhead lights are blinking, repeat steps 7 through 10 to replace the other printhead. Hp Officejet Pro K5400 Blinking Light Transkript Das interaktive Transkript konnte nicht geladen werden. Make sure that plain white paper is loaded in the input tray. The Devices and Printers window opens.

Reconnect the USB cable or the Ethernet cable to the rear of the product. Hp Officejet Pro K5400 Driver Press down firmly on the printhead to ensure proper contact. Disconnect the power cord from the rear of the product. Wait for the product to initialize the printheads and print an alignment page.

Hp Officejet Pro K5400 Blinking Light

Reinsert the printhead into the slot.

Align the cartridge with its color-coded slot, and then insert it into the slot. Hp Officejet Pro K5400 Clean Print Heads Release the Resume button, and then wait until the carriage is idle and silent. Hp Officejet Pro K5400 Manual OK, in the P.M.

Wait for the product to turn on or off, or to finish processing the current print job. navigate here Windows 7 On the Windows taskbar, click the Windows icon (), and then click Devices and Printers. Carefully remove any jammed paper or obstructions found. Press down firmly on the latch to make sure that it closes completely. Hp K5400 Troubleshooting

Use both hands to pull whole sheets of paper to avoid tearing them. Wird geladen... Disconnect the USB cable or the Ethernet cable from the rear of the product, depending on your connection type. http://orgias.org/hp-officejet/hp-officejet-pro-k5400-error-ky.html Reconnect the USB cable or the Ethernet cable to the rear of the product.

Apply a moderate amount of pressure to remove dust or dirt buildup. Hp Officejet Pro K5400 Printhead Lights Flashing Figure : Pull the paper tray out of Tray 2 Carefully remove any jammed paper and bits of torn paper from the paper tray and from under the product. Make sure that plain white paper is loaded in the input tray.

Close the duplexer access door.

The Devices window opens. Privacy Policy © Copyright 2016 HP Development Company, L.P. More Support Options Related Videos - of Video Tutorials | Show all Show less HP Download and Install Assistant HP Download and Install Assistant makes it easy to download and install your software.* Use HP Download and Install Assistant (recommended) Download only Remember my choice Cancel Next *Get more details on how HP installs software and gathers data to detect your products and provide relevant solutions Privacy Policy © Copyright 2016 HP Development Company, L.P. Hp Officejet Pro K5400 Ink Step three: Clear the paper jam from the front of the printer Lift the output tray.

Transkript Das interaktive Transkript konnte nicht geladen werden. Check your product warranty to determine if your product is still under warranty, and then go to Contact HP Support to schedule a repair or replacement. Important: Before you begin, make sure that the cartridges are compatible with your product. this contact form Step two: Clear the paper jam from the rear of the printer Choose from the following options to clear a paper jam from the rear of the product.

Reconnect the power cord to the rear of the product. Disconnect the power cord from the rear of the product. Cause There is an issue with one or both of the printheads. Close the duplexer access door.

NOTE: The product might go through a warm-up period of up to two minutes. Follow these steps to remove and reinsert the printhead.Make sure that plain white paper is loaded in the input tray.Press the Power button ( ) to turn on the product.Open the top cover. Wähle deine Sprache aus. Insert the duplexer into the rear of the product, and then push it forward until it snaps into place.

Transkript Das interaktive Transkript konnte nicht geladen werden. If one or more of the cartridges are missing, continue to the next step. Expert: romr2009 replied4 years ago. Open the top cover.

Wait until the warm-up period completes before continuing. Figure 3: Remove the rear access door Carefully remove any jammed paper and bits of torn paper from the rollers inside the product. Solutions Follow these solutions in the order presented to resolve the issue. Wiping the ink nozzles can damage the printhead.