Home > Hp Officejet > Hp Officejet Pro K5400 Error Lights

Hp Officejet Pro K5400 Error Lights

Contents

If the issue persists, continue to the next solution. The should stop the light from flashing. Close the duplexer access door. Solution one: Load paper Follow these steps to load paper if the product has run out of paper. Source

MacglobalusML 3,384 views 2:21 How To Clean Printheads - Duration: 2:50. Wait while the product initializes the printheads and prints the alignment page. Reply 0 0 PattiD Top Student Posts: 7 Member Since: ‎08-27-2014 Message 6 of 14 (478 Views) Report Inappropriate Content Re: Officejet Pro K5400 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎08-27-2014 12:04 PM Ok, Agemoz, I have done everything you suggested.W/regards to the printer use while I was gone, it's my office, I have the key and unless Jason Bourne let himself in while I was gone there was no one using it I think the problem is with the MC cartridge although at this time there are no yellow print head lights blinking.I have BOTH OLD printheads back in.When I replaced them one at a time the only printhead light that ever blinked was for the MCHOWEVER, despite having EVERYTHING unplugged from both power and computer for a total of 4 'timed' minutes, I still have 1 document in the print q that I can't delete even after powering off.My next thing is to power off my computer. Great performance.I am running Windows 7 and Office 2010.About 2 weeks ago I started getting lousy print quality. check that

Hp Officejet Pro K5400 Clean Print Heads

The lights indicate product status and are useful for diagnosing printing problems. You can also purchase genuine HP cartridges and supplies from other retailers. Remove the duplexer.

If the issue persists, continue to the next solution. If these steps resolved the issue, you do not need to continue troubleshooting. Press down firmly on the latch to make sure that it closes completely. Hp Officejet Pro K5400 Printhead Lights Flashing Solution three: Replace the printhead Make sure that plain white paper is loaded in the input tray.

Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... Hp Officejet Pro K5400 Troubleshooting note: If the paper tears when you remove it, check for any torn pieces of paper inside the product. Figure 33: Lift the printhead latch Image: Lift the printhead latchRaise the handle on the printhead that is indicated by the blinking light on the control panel, and then use the handle to remove the printhead from the slot. http://support.hp.com/us-en/product/HP-Officejet-Pro-K5300/K5400-Printer-series/2511747/model/2511764/troubleshooting/ The product is processing a print job.

NOTE: Ink level warnings and indicators provide estimates for planning purposes only. Hp Officejet Pro K550 Troubleshooting Disconnect the power cord from the rear of the product. If the cartridges are out of ink, follow these steps to replace them. caution: Wipe the electrical contacts only.

Hp Officejet Pro K5400 Troubleshooting

An easy fix! - Duration: 7:47. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting. Hp Officejet Pro K5400 Clean Print Heads sistemasz 168,872 views 4:43 INFORTEC BULK INK HP PRO K5400 - Duration: 2:50. Hp Officejet Pro K5400 Manual Wait at least 15 seconds.

Reply 0 Re: Officejet Pro K5400 Printer. 08-29-2012 10:30 AM Well, I have solved the problem. this contact form If the message displays, follow these steps. Figure : Open the cartridge door If all cartridges are in the carriage, skip to the next solution. To ensure peer review we are only allowed to use this website to communicate.Check back here tomorrow. Hp K5400 Clean Print Heads

Figure : Lift the output tray Carefully remove any jammed paper and bits of torn paper from the front of the product. justprintingaround 128,082 views 12:41 Unblock Printer Heads Clean - Remove Clogged Ink with ease - Duration: 3:26. Lock the duplexer into place. have a peek here Figure : Paper path top zone Reattach the rear access door.

Figure : Open the cartridge cover Remove the new cartridge from its package. Hp Officejet Pro K5400 Printer If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. Figure : Insert the cartridge and close the cartridge door Issue: The Power light and the Resume light blink, and one or more Print Cartridge lights are on In this error condition, the following light pattern displays on the control panel: Print Cartridge lights: On Printhead lights: Off Cancel button: Off Resume light: Blinking Power light: Blinking Figure : The Power light and the Resume light blink, and one or more Print Cartridge lights are on Cause One or more cartridges are expired.

Step one: Clean the rubber paper feed rollers Press the Power button () to turn off the product.

Press the Power button () to turn on the product. Figure 74: Remove the cartridge Remove the new cartridge from its package. Insert the duplexer into the rear of the product, and then push it forward until it snaps into place. Hp Officejet Pro K5400 Ink Insert the door into the rear of the product, and then gently push it forward until it snaps into place.

Align the cartridge with its color-coded slot, and then insert it into the slot. Close Yeah, keep it Undo Close This video is unavailable. Follow the on-screen instructions to order new supplies or check cartridge compatibility with your printer. http://orgias.org/hp-officejet/hp-officejet-pro-k5400-error-ky.html Sign in 6 0 Don't like this video?

Figure 79: Insert the cartridge and close the cartridge door Issue: The Power light and the Resume light blink, and one or more Print Cartridge lights are on In this error condition, the following light pattern displays on the control panel: Print Cartridge lights: On Printhead lights: Off Cancel button: Off Resume light: Blinking Power light: Blinking Figure 80: The Power light and the Resume light blink, and one or more Print Cartridge lights are on Cause One or more cartridges are expired. Release the Resume button, and then wait until the carriage is idle and silent. Press and hold the Power button (). note: Make sure that the label on the printhead matches the label on the printhead latch.

Figure : Rotate the rollers Allow the rollers to dry for 10 to 15 minutes. Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Solutions Follow these solutions in the order presented to resolve the issue. Figure : Lift the output tray Check for any jammed paper or scraps of torn paper, and then remove the jammed or torn paper by pulling it toward you.

Scroll to the bottom of the page, and then make sure the country/region location is correct. Reach inside the main paper path access area (compartment 2), and then manually move the carriage. The outside of the product might not look the same as your product, but the steps are the same. . If you have trouble viewing the video, or to view the video in a different size, click here to play the video on YouTube.

Use both hands to pull whole sheets of paper to avoid tearing them. Reach inside the product, and then manually move the carriage.