Home > Hp Officejet > Hp Officejet 7210 Error Message

Hp Officejet 7210 Error Message

Step two: Align the All-in-One Print another alignment page. How does HP install software and gather data? If the alignment succeeded and the page printed correctly, stop troubleshooting. HP Support Forums Join in the conversation. Source

The carriage chute is the side wall of the carriage that holds a curved metal piece, called the x-bias spring.Figure : Carriage chute and x-bias springCarriage chuteX-bias springOpen the product cover and wait until the carriage is idle and silent.Remove the cartridge.Looking in through either the cartridge access door or the output paper tray, look for a small plastic tab or the x-bias spring around the carriage area. Reconnect the power cord to the rear of the product. Discard or recycle the page that prints. HP Officejet 7200, 7300, and 7400 All-in-One Printer Series - 'Press OK to align cartridges' Error Message Displays on the All-in-One Issue After you insert a cartridge, the error message 'Press OK to align cartridges' displays on the control panel.

A MESSAGE SAYING REMOVE & CHECK COLOR CARTRIDGE Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎05-29-2012 10:50 AM I HAVE A HP OFFICEJET 7210 ALL-IN-ONE. The alignment page contains rows of horizontal and vertical bars of varying sizes. Press 6 to select Tools, press 2 to select Align Print Cartridge, and then press OK.

It has not been out of the printer nor has the printer been moved. note: Never clean the cartridges unnecessarily. Tap water can contain contaminants that damage the cartridges. Examine the test page.

If the alignment failed or if there are missing colors or gaps in the bars, continue to the next solution. Press 6 to select Tools, press 2 to select Align Print Cartridge, and then press OK. Use bottled or filtered water if distilled water is not available. I have an HP 5610 and an HP 1315v, and they are both displaying the same message.

Step two: Align the All-in-One Print another alignment page. Up to three levels of cleaning are available. On the product control panel, press the Setup button. Click Here Make sure you don's see any damage in the ink carriage area.

Slide the stack of paper forward until it stops. Step one: Clean the cartridge and carriage contacts Follow these steps to clean the contacts on the cartridges and the contacts on the carriage inside the product. Reply 0 Re: Error Message-Print Cartridge 09-04-2011 07:16 AM I finally removed the "offending" cartridge and replaced it with a new HP cartridge and, now, my printer is working fine - no error messages and the print is perfect. note: HP cannot guarantee the quality of remanufactured or refilled cartridges.

By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! http://orgias.org/hp-officejet/hp-officejet-pro-8600-error-message.html Figure : Close the latch Repeat these steps for the other cartridge. Do not overload the input tray. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Press down lightly on top of the latch, and then pull out the bottom of the latch to unhook it. Figure : Load paper into the input tray Slide the paper length and width guides inward until they stop at the edges of the paper. have a peek here Reply 0 0 cabhoney Honor Student Posts: 2 Member Since: ‎09-03-2011 Message 4 of 7 (2,054 Views) Report Inappropriate Content Re: Error Message-Print Cartridge Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎09-04-2011 05:12 PM I have also done this, so not the answer for me.

Open the Printers folder. Complementary Content Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Solution seven: Reset and align the All-in-One Follow these steps to reset, and then align the product.

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page « Message Listing « Previous Topic Next Topic » Moose_1492 Honor Student Posts: 2 Member Since: ‎08-04-2015 Message 1 of 3 (403 Views) Report Inappropriate Content Printer error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎08-04-2015 12:48 AM Product Name: Officejet 7210 Operating System: Microsoft Windows 7 (64-bit) I have the following error message in the display on the printer:Error: 0x07d54dd62005: lib_barracuAlso, the following buttons are flashing:On Button; the Copy quality button; Auto Answer buttonHow do I fix this?

Scroll down and click on: HP contact options - click on Get phonenumberCase number and phone number appear.I hope this helps. If the alignment failed or if there are missing colors or gaps in the bars, continue to the next solution. If the issue persists, see the next step. Any suggestions?

By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Press 6 to select the Tools menu, and then press 2 to select Align Print Cartridge. I'd be perfectly happy if I could just make the printer ignore colour cartridges and carry on as a monochrome machine.But more than anything......I WANT TO BE ABLE TO ENTER THE SETUP MENUS SO I CAN SET THE DATE, TIME, AND NETWORK PARAMETERS, TO CONTINUE TO USE THE SCANNER AND MEMORY CARD READER!!! Check This Out Reply 0 0 Moose_1492 Honor Student Posts: 2 Member Since: ‎08-04-2015 Message 3 of 3 (340 Views) Report Inappropriate Content Re: Printer error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎08-11-2015 04:16 PM It worked, thank you very much for the quick response.

Ask the community! Step four: Align the All-in-One Align the product again.