Home > Hp Laserjet > Hp Printer Error Lights Red Green

Hp Printer Error Lights Red Green

Contents

CAUTION: Do not remove jammed paper at this stage. Carefully rotate the rollers up to clean all the way around. The self-test report prints. Issue: Print Cartridge light blinking Solutions for Print Cartridge light blinking This blinking lights pattern indicates one of the following conditions: The print cartridge has rotated and is now accessible. Check This Out

On the Printer Services tab, click Print a Test Page. Figure 13: Slide paper guides inward Step seven: Print a self-test report Follow these steps to print a self-test report to test the product hardware. Figure : Open the cartridge latch to remove the cartridge Remove the new cartridge from its package, and then carefully remove the protective tape. If the Wireless light is still blinking, continue to the next step. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02497683

Hp Laserjet P1102w Blinking Orange Light

Make sure that the carriage can move freely across the width of the product. Connect the power cord to the rear of the product. If the printer does not turn on with the alternate power cord, continue to the next step to service the printer. Gently push the carriage to the left and then to the right.

Figure 33: Press the print cartridge button Open the print cartridge door. How to print a self-test report Choose one of the following options to print a self-test report. Figure : Ready light blinks Issue The Ready light blinks. Hp Laserjet P1102w Blinking Red Light Press and hold the Resume button () for two to three seconds, and then release the button.

If the issue persists, see the next solution. Hp Laserjet P2035 Error Lights NOTE: If the product prints when plugged directly into a wall outlet, the power strip or surge protector might not be allowing enough voltage to reach the product. While holding the Power button, press the Resume button () four times. http://support.hp.com/us-en/document/c01237241 Determine the issue, based on the icon the yellow arrow points to, and then expand that section for solutions.

If so, allow the carriage to move to that position. Hp Laserjet 1320 Blinking Orange Light caution: Do not remove jammed paper at this stage. Reconnect the power cord to the electrical outlet. Windows Vista: Click Start, and then click Control Panel.

Hp Laserjet P2035 Error Lights

Press the Power button () to turn off the product. check this link right here now Figure 73: Open the cover on the product Open the cartridge latch, and then slide the cartridge out of its slot. Hp Laserjet P1102w Blinking Orange Light Remove the rear access door Turn the knob on the rear access door counter-clockwise to release the door, and then pull the door toward you to remove it Figure : Remove the rear access door Remove the duplexer Press the buttons on each side of the duplexer, and then pull the duplexer toward you to remove it. Hp Laserjet P1102w Blinking Green Light Make sure the door snaps firmly into place. (Do not press the buttons on the ends of the duplexer when you reattach it.) Press the button on top of the duplexer to open the duplexer door.

Step one: Perform a power reset Follow these steps to reset the product. his comment is here When the supply has reached this condition, the HP Premium Protection warranty for that supply has ended. Figure 24: Remove the duplexer Gently remove the jammed paper from the product. Press the buttons on each side of the duplexer, and then pull it toward you to remove it. Hp Laserjet P1102w Blinking Blue Light

Method two: Remove the duplexer to clear the paper jam from the rear of the printer Press the Power button () to turn off the product. Remove any loose paper or obstructions found. Issue: The Power light and the Resume light blink simultaneously The following light pattern displays on the product control panel: Cartridge light: Off Resume light: Blinking Power light: Blinking Figure 45: The Power light and the Resume light blink simultaneously Cause The carriage might be stuck. http://orgias.org/hp-laserjet/hp-printer-meanings-error-lights-red-green-triangle.html Do not touch the cartridge shutter or the roller surface.

Step five: Print a self-test report Print a self-test report to make sure that the hardware functions correctly. Hp Laserjet 1020 Red Light Error Turn the knob on the door clockwise to lock it into place. Allow up to three minutes for the product to calibrate.

note: You can also open the HP product software from your computer desktop: double-click the icon for your HP product.

Close the cover on the product. Press the Power button () to turn on the product. The self-test report prints. Hp Laserjet P1102w Error Lights Determine the issue, based on the icon the yellow arrow points to, and then expand that section for solutions.

HP Support Forums Join in the conversation. Disconnect the power cord from the back of the product. If the Wireless light is still blinking, continue to the next step. navigate here Step four: Print a self-test report Choose one of the following options to print a self-test report.

Issue: The Power light is on The following light pattern displays on the product control panel: Cartridge light: Off Resume light: Off Power light: On Figure : The Power light is on Cause The product is ready to process a print job. Figure : Open the cover on the product Carefully remove any jammed paper from the front of the product. Load paper into the input tray Load plain paper print side facing up into the input tray. Press the buttons on each side of the duplexer, and then gently push the duplexer back into the rear of the product until it snaps firmly into place.

Plug the power cord back into the wall outlet. Figure : Rock the print cartridge Insert the print cartridge, and then close the print cartridge door. Carefully rotate the rollers up to clean all the way around. Issue five The print cartridge is not installed.

Solutions Follow these solutions to resolve the issue. If the issue persists, see the next solution. Option one: Print a self-test report from the control panel Press and hold the Power button (). If the issue persists, continue with the next solution.

Solution three: Clean the paper rollers Follow these steps to clean the paper rollers.