Home > Hp Laserjet > Hp P3005 Replace Dimm Error

Hp P3005 Replace Dimm Error

Contents

The average user does not treat these units with care, nor do they care. We have moved away from HP and are working with Xerox and Epson. Once open it shows the formatter board. Clearing paper path The device jammed or detected misplaced media. http://orgias.org/hp-laserjet/hp-printer-error-memtest-failure-replace-dimm-0.html

Sleep mode on The device is in the sleep mode. Just do it carefully and it works. Initially HP told me it was out of warranty and I would have to pay for the repair, but after a little persistence about the service note on these printers, I was able to get it repaired for free by an authorized HP service provider. You will see a metal door.

Hp Laserjet P3005 Mem Test Failure Replace Dimm 0

Was the information on this page helpful? HP said the same. Add × Loading... So, by far one of the most bizzare fix suggestions I've ran into, and also one of the most effective.

I am just reporting back what happened . I'm still amazed, take it apart and put it in the oven?!?!? You'll see a memory DIMM. Hp P3005 Cold Reset Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product?

Added memory also gives you more flexibility in supporting job-storage features, such as quick copying. Hp Laserjet P3005 Memory Use HP Web Jetadmin software to delete files from the storage device, and then try again. Contributor 9 Answers Re: memory test failure replace dimm 0 Formatter is bad. Tried to update firmware but get 'ftp: connect :unknown error number' Please advise Comments added : Jul 31, 2008 11:03:45 AM BST misroute Comments added : Jul 31, 2008 11:26:17 AM BST - by:Akroyd,David - Repeat attempts at power cycling this printer have generated these errors: 49.4C2D error and 49.FF07 Service Error Thanks a lot David Akroyd Comments added : Jul 31, 2008 12:33:00 PM BST Cust have mentioned that this fault is covered by the service note : Able to entitle the service note in WFM.

The one I use puts out over 1200 degrees, but people have had success using ordinary hair dryers. Hp Laserjet P3005 Hangs During Startup I have 75 P3005 printers and have not had a failure since all were upgraded. Reinstall the duplexer. Error messages Error messages communicate that some action must be performed, such as adding paper or clearing a jam.

Hp Laserjet P3005 Memory

Disable the print server. http://www.fixyourownprinter.com/posts/54166 Restoring The device is restoring settings. Hp Laserjet P3005 Mem Test Failure Replace Dimm 0 Dryed them with a hair blower and reassembled. P3005 Formatter Board by opcso on Jun 5, 2009 at 1:12pm Add comment Please sign in to comment 0 Just fyi I have the same problem with one of these printers that is about 5 months out of warranty.

If a critical error persists, service is required. this contact form If CLEARABLE WARNINGS is set to JOB on the device CONFIGURE DEVICE menu, the next print job clears these messages. Contact HP support. I had the same problems as most of you and followed the advice on contacting HP and quoting the service note. Hp Laserjet P3005 Replace Dimm 1

I kept the heat on & re-booted the printer again & the display then stayed black with no light at all & I thought well I am getting somewhere. by opcso on Nov 16, 2009 at 10:06am Add comment Please sign in to comment 0 yardsnotso tell me how to fix it:---... Then he is still freezes.Is the "printer freezing problem" also a problem from the formatter board? have a peek here So I opened the right side doorways to expose the formatter & put a good hot blow-dryer up to the bad chip on the top middle & let it get good & hot & turned on the printer -- it booted but the display was lit but blank & stayed blank.

CAUTION: To reduce the possibility of damage caused by static electricity, always wear an electrostatic discharge (ESD) wrist strap or touch the surface of the antistatic package before handling DIMMs. Install A Supported Memory Dimm. I thought the idea of putting the boards in an oven was a little extreme but then again what do you have to lose? or If the message persists after clearing all pages and exiting Help, contact HP Support. 13.XX.YY JAM INSIDE REAR DOOR alternates with Clear jam then press (SELECT) A jam has occurred in the duplex reversing area.

Cleaning...

or Press (HELP) for help. Posted on Jun 25, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Catballoons 8 Answers SOURCE: Hp P3005Getting error 49.4C2D and replace dimm. Hi

Slide the side cover of towards the back of the printer.

Open the metal door.

pull out the three wiring plugs from the top of the board, they only go in one way so you don't need to mark them.

Undo the screws around the board and pull the board free.

Using a hot air paint stripper with the adaptor that concentrates the heat into a point, heat up the reverse side of the board with plenty of heat on the soldier joints.

Reassemble

Do a cold restart and hopefully away she goes.

Works for me.
Chris


Posted on Aug 12, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great answer: - Answer the question. - If you need clarification, ask it in the comment box above. - Better answers use proper spelling and grammar. - Provide details, support with references or personal experience. If desired, you can replace a DIMM installed in the slot with a higher memory DIMM. Hp P3005 Service Manual by unknown on Dec 22, 2008 at 8:42am Add comment Please sign in to comment 0 I tried removeing the battery for 10 minutesno change.

I can not say about other countries or locations. by moe on Nov 14, 2009 at 8:41am Add comment Please sign in to comment 0 Are you kidding me?!?!?!I fought with this exact problem that's been described here forever. Other than that the procedure should work just fine as long as you keep the oven at 350 degrees F and keep in the oven for exactly 8 minutes. Check This Out A JetDirect card show fair just fine.Top-side surface mount parts have to be baked in the manufacturing process, while the bottom parts are usually glued on and run through the the wave soldier.However, I just did 5 min @ 400 deg F on a P3005n formatter and smoked two of the large through-hole capacitors...Not like I had much to lose.

Duplex registration is not available when the tray size is set to either of these settings. I have had replacement boards fail. it flashed said I think that the firmware flash completed on the printer display, then the printer started to eject blank pages, Now I get the download firmware ...etc message. HP told me via the phone that there is "no recall information for this product".

I earlier scrolled through all of the documents and could not find the one listed previously. PAPER PATH JAM FRONT DOOR alternates with For help press (HELP) A page is jammed in the paper path.