c. Defective formatter board. Press (Down Arrow) button once. Pull open the front cover. Source
The control panel will display COLD RESET . Open the top cover. Leaving the shipping blocks in the fuser prevent the paper sensor from moving and cause the error. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.
Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. X Description 0 on board NVRAM 1 removable disk (flash or hard) Solution: 1 For 68.0 errors, turn the printer off and then on. 2 If a 68.0 error persists, perform an NVRAM initialization. 3 For 68.1 errors, use the HP Web Jetadmin software to delete files from the disk drive. 4 If a 68.1 errors persists, reinitialize the hard disk. 5. Turn on the printer. Press (Down Arrow) button once.
When the memory starts counting, press and hold the green (Select) button. Adjust all trays to the correct paper size. The control panel will display SELECT LANGUAGE . Action Press (Select) to clear the message and continue.
Replace memory SIMMs. RE: 68.0 Permanent storage error DiStefano (TechnicalUser) (OP) 2 Nov 03 16:21 If you boot the printer this comes up on display, "68.0 permanent storage error, check settings"Nothing has been inserted into the printer. The control panel will display SELECT LANGUAGE . Clean the color registration detection sensor above the black print cartridge if the error does not clear.
Action Lift the top cover. Reinstall fuser. If the error persists, reinitialize the hard disk or flash DIMM. If the error returns try a different EIO slot.
Critical error messages Critical error messages display warnings about device failures. Printer Memory Printers can use a surprising amount of memory and it is not unusual for large, fast machines to be fitted with a hard disk. If the message is not cleared, turn the MFP off, and then turn the MFP on. 3 Determine which settings have changed by printing a control panel menu map. 4. Not really relevant but possibly useful.
The printer will perform a cold reset and then continue its power-on sequence. http://orgias.org/hp-laserjet/hp-laserjet-iip-error-12.html The control panel will display SELECT LANGUAGE . Possible printer control panel error message 41.1 unknown misprint error 41.2 beam detect misprint error 41.3 media feed error (size) 41.4 no VSYNC error 41.5 media feed error (type) 41.6 ETB detection error 41.7 feed delay error 41.9 noise VSREQ Action Press (Select) to continue or press ? (Help) for more information. See below: Error Message Toner sensor 54.21 Yellow Toner Remaining Sensor 54.22 Magenta toner Remaining Sensor 54.23 Cyan Toner Remaining Sensor 54.24 Black Toner Remaining Sensor Action Turn the printer off, and turn it on again.
Force a calibration by selecting CALIBRATE NOW or QUICK CALIBRATE NOW from the Print Quality Menu . X PRINTER ERROR FOR HELP PRESS ? top 13.05.00 JAM IN PAPER PATH X For help press ? have a peek here Replace the cyan cartridge If this message persists, contact an HP-authorized service or support provider.
If the 49 error returns, turn the power off, and then unplug the printer. Watch the control panel. Action Turn the printer off, and then turn on the printer.
alternates with TO CONTINUE PRESS 68.X PERMANENT STORAGE ERROR SETTING CHANGE FOR HELP PRESS ? Action Lift the top cover. Action Turn the printer off, and turn it on again. Check This Out The control panel will display SELECT LANGUAGE .
The control panel will display SELECT LANGUAGE . Check the paper pickup assembly for jammed media. In most situations, use a cold reset rather than a NVRAM initializationto reset device settings (this will retain the values in the SERVICE menu).NOTE Before performing a NVRAM initialization, print a menu map and a configuration page(see Use information pages on page 38). Release the GO button after all LEDs flash once and then turn on solid.
top 54.16 PRINTER ERROR Description There is a problem with the Magenta CPR sensor. Action Turn the printer off, and turn it on again. Use the information on the configuration page to resetany customer-set device configuration values that the NVRAM initialization procedure changes.Take special note of thetotal page count, maintenance count, and the serial number.1. If the error persists, contact HP Customer Care Support.
Replace the specified DIMM 64 PRINTER ERROR alternates with CYCLE POWER A scan buffer error occurred 1. If this message persists, contact HP. If the 80 SERVICE error continues, remove and reinstall the Jetdirect card, installing the card in the other EIO slot provided in the printer.