X=2: Laser malfunction. 52 ERROR (Incorrect Scanner Speed) 1. HP LASERJET 4350 TRAY 2 CASSETTE DOES NOT OPEN Q: We have an hp laserjet 4350 printer with a tray 2 cassette that is not opening when we try to load paper. What would cause the 4350 paper tray to get stuck? Perform a cold reset. 2. A: It is not uncommon for hp laserjet 4300 printers to loose their network connectivity especially since they were outfitted with the 615 network cards. Try printing the network configuration settings. They most likely will not be available. This being the case we will probably be looking at a faulty network card or if not a faulty formatter. HP laserjet 43000 error 21 Printer cannot process the page quickly enough Hp laser 4300 error 22 eio Printers eio card in the slot has overflowed its I/O buffer HP laser 4300 error 22 parallel I/O The parallel buffer has overflowed during a busy state Hp 4300 error 22 parallel I/0 Buffer overflow The parallel buffer has overflowed during a busy state HP laserjet 4300 error 40 EIO bad transmission The connection with the card in the eio slot has been broken abnormally HP 4300 error 41.3 unexpected paper size in tray The media that is loaded is longer or shorter in the feed direction than the size that is configured for the tray HP laserjet 4300 error 41.1 A printer error has occurred unknown misprint error HP 4300 41.2 error A printer error beam detect misprint error HP laserjet 4300 41.4 no vsync error No vsync error HP 4300 error 41.7 feed delay error HP laserjet 4300 41.9 signal noise error HP 4300 error 49. have a peek at this web-site
Replace DC Controller PCA. 2686 Only: 1. For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect. 22 ERROR/ I/O CONFIG ERROR 1. If the latest firmware image version is newer than the one installed on the device, upgrade the device, if possible. 3. and may not be used without advance written permission of PrinterTechs.com, Inc.
Simplify print job. 2. Inspect toner level sensor connector for damage. 4. IIISi/4Si Only: 1. Check that ROMs are in correct location and orientation. 3.
At least one of two tabs must be present. Replace fuser. Replace Interface/Formatter PCA. Hp Laserjet 600 Hard Drive If the message will not clear: 1.
III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card. 99.09.67 Error Note IIP, IIP+, IIIP: Short C212 on the DC Controller to bypass error 50 time delay. (The printer must be turned off.) IIISi/4Si Only: 1. Check Duplex Shift Plate for correct operation. 2. Make sure that the side of the tray is empty.
Computer and printer may be set to different baud rates. 2. Check PS701 and PS703 13.20/13.32 Paper stopped jam in paper path. Error 99.09.64 Hp A temporary scan-buffer printing error.2. Hp Laserjet 600 M602 Formatter Board Replace formatter board.
Top cover open. 2. http://orgias.org/hp-laserjet/hp-laserjet-iip-error-12.html Turn printer off and on.3. HP LASERJET 4250 ERROR 60.02 Q: I have an hp laserjet 4250 error 60.02 that wont seem to go away. What causes this error 60.02? Replace cable, Fuser to DC Controller, connector J206. (P/N RG1-0907-000.) 2. Hp M601 Hard Drive
Inspect cable assembly to DC Controller. 2. Computer is powered off. 3. Remove Dimms, cycle power 4. Source Tab missing on top cover. 5. 220V unit plugged into 110V outlet.
Inspect the Fiber Optics Cable for cuts or kinks. 2. Hp Printer Error Codes List Check/reseat cable between DC Controller and Formatter PCA. 56 ERROR IID, IIID Only: 1. Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4.
Replace the specified DIMM 64 PRINTER ERROR alternates with CYCLE POWER A scan buffer error occurred 1. Bad laser unit or improper laser power setting. 2. Check duplex paper path for obstructions. 2. have a peek here Broken separation belt. 2.
I/O card is unable to accept data or is not connected to the network. 30 PS ERROR XX 1. Replace DC controller. On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Our technicians can help you fix your printer Contact Us HP LaserJet M3035 MFP Printer Error Codes and Support Error: 64 ERROR Error Description: A scan buffer error occurred. Check connectors J204 and J6 on DC Controller and conenctor at Fan 1. 2.
A: When your hp laserjet 4250 perform printer maintenance message appears on your display panel it is time to install a hp laserjet 4250 maintenance kit (q5421a). The printer is programmed to display that message after 200,000 pages have been printed out of the printer. The rollers and fuser assembly are rated for 200,000 prints give or take depending on operating environment and media. Much like any other consumable part, after a certain amount of use they are required to be replaced. Purchasing a maintenance kit and installing will get your HP laserjet 4250 running as it should. Wrong I/O cable. 3. Check tabs on side of toner cartridge. Replace Firmware Dimms. 5.
Replace the duplexer 79 SERVICE [XXXX] The printer detected an error. 1. A: HP laser 4300 error 60.2 problems indicate that their has been a malfunction with the lifter motor in the tray 2. This can be caused by a faulty lifter motor or a component that is causing the lifter motor to malfunction. An inspection of the lifter motor and all those parts that the lifter motor engages typically will reveal the cause of the error 60.2 HP LASERJET 4300 MAKING A GRINDING NOISE Q: Our hp laser 4300 is making a grinding noise when we are printing. It has been making a grinding noise for some time though it is gradually getting worse and worse. The printer seems to be working fine though it is really starting to sound like something is about to give. I have heard that hp laser 4300 making grinding noise is a relatively common problem. How do we go about repairing this issue A: HP laserjet 4300 making grinding noise is a common problem and is typically isolated down to a couple parts. One being the hp laser 4300 fuser assembly and the other being the hp laser 4300 swing plate assembly. The two engage each other and can when the gears wear, make the noises that you are describing. By replacing those you will sure fix your hp 4300 grinding noise problem HP LASERJET 4300 LOST NETWORK CONNECTION Q: Our hp laserjet 4300 lost its network connection the other day and I was wondering if there are any known problems with these printers that can cause them to do this? I have since tested the network ports and the cables though they are working just fine. Ideas? Reseat jetdirect card - Network card.4. IIISi/4Si Only: 1.
This will clean up the permanent storage by removing old areas that are not being used. 69.X PRINTER ERROR alternates with CYCLE POWER TO CONTINUE A temporary printing error occurred. Replace the formatter. 79 & 80 errors - general info. Replace Duplex unit. 54.1 Remove sealing tape - 4100 only: Toner cartridge has been installed without removing sealing tape 54.4 error - 4100 only: Problem exists with customers line voltage 55 ERROR (Internal Communication Problem) 1. II, III Only: 1.
External fuser access door not closed. 4P/5P Only: 1. Check PostScript ROMs. 40 ERROR (DATA TRANSFER ERROR) 1. HP LASER PRINTER 2300 1.