Use the event log page and event log codes to aid in isolating where the errors are occurring. LaserJet 9000/9040/9050 Fuser error and power supply failure! If an optional output device is installed, push it back into place. LaserJet 9000/9040/9050 printer repair with error code 13.XX.YZ JAM INSIDE LEFT DOOR 13.06.00 a fuser delivery stay jam has occurred, and the media did not clear PS501 within the specified time. http://orgias.org/hp-laserjet/hp-laserjet-error-64.html
After two days of head pounding, and two new DC controllers, a new fuser, and other replacments. If a message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: Click here for information on contacting HP Customer Care. If so, what is it? Tray 2: The media did not reach the tray 2 feed sensor (PS1402) within the specified time.
Somebody....anybody....help! Replace the output device controller PCA. 68.X The printer NVRAM or hard disk is failing to write . key to view the Help. Wird geladen...
If just a message and no motor action in the printer, then look for a shred of paper, most likely in the registration assembly. The User's Guide that came with your HP product. Open and close the front door to clear the message. try this Figure 10: Moving the output device away On the stacker, lift the wire on Bin 2 of the device, and carefully pull out any paper from this area (Figure 11).
Error 13.20.00 JAM INSIDE FRONT DOOR 13.20.00 a page is jammed in the paper path. Carefully check to be sure that all pieces of torn paper have been removed. An auto-flush operation is not possible. A lifting operation is not completed in the correct amount of time.
Inspect the paper path and all paper path mechanical assemblies prior to the leading jam. Check This Out If YES Error, Remove jetdirect and power on the printer. Recommended action The EIO card may need to have its firmware upgraded or there may be a communication issue on the network. Since the paper sensor behind the door did't sense any paper, the machine assumed a jam.
The leading edge of the media did not reach the fuser delivery sensor (PS502) within the specified time. 13.06.00 JAM INSIDE FRONT DOOR 13.06.00 a page is jammed in the paper path at the fuser area. 13.06.00 JAM INSIDE LEFT DOOR 13.06.00 a page is jammed in the paper path at the fuser area. With the network cable unplugged it works fine when I plug the cable in and it tries to process the jobs sent to it it gives the message 49.4C02 Error turn off and on to clear. Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. http://orgias.org/hp-laserjet/hp-laserjet-error-54-2.html and may not be used without advance written permission of PrinterTechs.com, Inc.
Click here for information on clearing staple jams from the multifunction finisher. Carefully check to be sure that all pieces of torn paper have been removed. this is the first time i encounter this promlem.
Anmelden Dieses Video gefällt dir nicht? After that it stays in the left door. For tray 4, make sure that all adjustments are set correctly; front, back, and side at the top and bottom of the tray. The misalignment of the paper guides usually occurs when the tray has been forcefully shut.
Figure 5: Lifting the green tab in the jam access area Remove any paper from this area by pulling it out of the printer. The EEPROM on the controller PCA is damaged. Remove two cable connectors, and it should pull away for the side, where it can then be removed. http://orgias.org/hp-laserjet/hp-laserjet-error-52.html Push the output device back into place.
If this does not resolve the error then the compact flash card may need to be replaced. The printer is under warranty, but HP don't haveany parts. The problem was actually with the DSS software that the user was using to send emails and other workflow related stuff. I know for a while they were replacing the 615's as they failed even if they were more than a year old (but I'm not sure if they are still doing that).49 errors are communication errors, not always related to the firmware (although firmware is the number 1 cause of these errors).
Figure 26: Moving the output device away from the product Open the left door and carefully pull any paper from the area (Figure 27).