Home > Hp Laserjet > Hp Laserjet 51.1 Error

Hp Laserjet 51.1 Error

Contents

The product has experienced an internal hardware error.2. Make sure that the door is completely open. 2.  Disconnect one connector, and then remove one screw. 3.  Slide the control panel toward the front of the product to release it. 4.  Lift the control panel off of the product. This dual line scanning enables the printer to create its true 1200 dpi image and keep printing at 25 ppm. The one I ran into it was right on the display and the machine wouldn't do anything. Source

PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My Account Checkout Home Troubleshooting 51.01 51.1 Error HP LaserJet 4100 Laser scanner failure Email 51.01 51.1 Error HP LaserJet 4100 Laser scanner failure  The 51.01 and 51.1 errors are fairly common error codes on the HP LaserJet 4100, 4100N, 4100TN, and 4100DTN series printers.  This error indicates a failure with the laser scanner assembly, which is a high-failure part on these models.  You can try turning the printer on and off; sometimes that will temporarily reset the error code and allow you to print a few more pages.  Usually the error reappears, in which case you should replace the laser scanner.  Fortunately, on this model replacing the laser scanner is not a difficult repair; see instructions below. HP LASER PRINTERS 5000, 5100 1. Reinstallation tip Make sure that you correctly reconnect the FFC  when the laser/scanner is installed. Replace the laser scanner assembly. 4.

51.10 Error P3015

The information below provides an explanation of the error and the recommended action to be taken. Turn the product on. 3. Replace laser scanner ass'y.3. Defective laser scanner assembly.

The risk of not monitoring this is too great, and it would be easier, not to mention less expensive, to monitor the double pulse than it would be to monitor the current or on/off pulses in extra circuitry on the laser pca. Reseat cables to the laser scanner and ECU. 5. surabaya rock band mp3 says: February 1, 2016 at 4:15 amHarmonix has released four mainline titles within the Rock Band collection: Rock Band (2007), Rock Band 2 (2008), Rock Band three (2010), and Rock Band 4 (2015). Hp Laserjet P3015 Error Codes Replace the scanner ass'y4.

When a print is first created, the laser beam is turned on which allows it to bounce off the beam detect mirror and reflect over to the beam detect sensor. Open the rear door. 2.  Gently pull down on the door and lower the door until it is fully open. 3. They said if I knew exactly what part of the scanner was broken, I could order that instead of the entire scanner. This Site This theory again points to a laser beam failure.

Last edited by coodbgood; 03-25-2005 at 11:48 PM. 51.10 Error Hp 4250 controller board.HP COLOR LASER PRINTER 4600, 5500 ERROR 51.X01. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. The Weak Link The weak link in relation to this 51.1 error revolves around the laser, beam detection loop.

Hp P3015 Laser Scanner Assembly

The errors appear to be intermittent, separated by 1000s of pages, or as little as a hundred. http://www.imagesourcemag.com/ism-article/511-errors-4100-printers HP LaserJet Printer maintenance kits should be replaced at every 200,000 to 350,000 pages to avoid print defects and paper jam problems. 51.10 Error P3015 Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. Error 51.10 Hp Laserjet P3015 Solution Note: this message will only appear in the Configuration Menu if the PERFORM USER MAINTENANCE message appears.

Replace the cable ass'y from scanner to D.C. http://orgias.org/hp-laserjet/hp-laserjet-iip-error-12.html Our printer technicians are HP experts, trained to replace HP LaserJet printer maintenance kits Our technicians carry high demand LaserJet maint kits for HP Color LazerJet,, Laser-Jet Fax and Lazer and Jet MFP. Cables Possibility Cables are listed as the fourth possibility but the likelihood of them causing the failure is small. System error 21:11 A problem has been detected with the Service Station assembly. Hp Laserjet P3015 Laser Scanner Assembly Replacement

The hold up recently in printing true 1200 dpi has been the drum rotation speed, which correlates with the paper path speed. A message New Maintenance will appear in the control panel display and the printer will reset. This could explain the intermittent occurrence of this error and is now a question we are asking our customers when their printers are displaying a 51.1 error. have a peek here Fold down the rear output bin at the back of the printer, and remove 2 screws (see picture, screws circled as #1) hidden underneath the lip of the top rear of the printer.   Next, remove 2 screws from the front of the top cover, circled as callout 2 in picture below.

HP LASER PRINTERS 1200, 2200, 2300,2410, 2420, 2430, 3100 FAX, 3200 FAX, 4100, 4100MFP 1. Hp P4015 Laser Scanner Feel free to give us a call with questions:  toll-free 866-352-7108 or local 608-831-2396. If the display panel on your HP LaserJet printer reads "PERFORM PRINTER MAINTENANCE" your HP LaserJet printer needs a maintenance kit, which includes a fuser unit and separation rollers.

X Description: hp 4000 50.1 is Low Fuser temperature 50.2 is Fuser warm up service 50.3 is High Fuser temperature 50.4 is Low/Bad line voltage (Printer hooked up to UPS) 50.5 is Inconsistent Fuser. 51.

System error 73:04 Server error. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Temporary error. / Bad toner cartridge 2. 51.10 Error Hp 9050 Replace the DC controller PCA.

System error 71:04 Problem allocating memory. X=1 Beam detect error X=2 Laser error Y=0 Black laser 2. System error 04:11 Jet direct network card not detected. Check This Out Remove one screw, and then slide the formatter cover toward the back of the product to release it. 2.