Home > Hp Laserjet > Hp Laserjet 4350 Error Codes

Hp Laserjet 4350 Error Codes


by unknown on Dec 24, 2013 at 9:55am Add comment Please sign in to comment 0 Ok, so now it says something completely different. 49.235f SERVICE ERROR. TOO MANY PAGES IN JOB TO STAPLE The maximum number of sheets the stapler can staple is 15. Also the paper feed/registration sensors could be knocked out of place. Replace the cartridge in the stapler unit. 8 Close the staple unit. 9 If the error persists, replace the staple cartridge. 10 If the error persists, replace the stapler unit. Source

by unknown on Jun 14, 2013 at 6:09am Add comment Please sign in to comment 0 Hello. CARD SLOT X FILE SYSTEM IS FULL To clear press Product illustration alternates with The CompactFlash card in slot X is full. Please wait while we process your request. See Dc controller PCA. 49.XXXX PRINTER ERROR To continue turn off then on A critical firmware error has occurred that caused the processor on the formatter to abort the operation. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=412160

Hp Laserjet 4250 Cleaning Page

See Printer switches and sensors. 5 Replace the dc controller PCA. If the fuser does not click into place you run the risk of wearing out both the fuser and the gears that drive the fuser prematurely. See Dc controller PCA. 58.4 Power supply 1 Replace the power-supply assembly. Thanks...

HP 4350 64 PRINTER ERROR A temporary printing error occurred in the scan buffer. See Configuration page. 4 Verify that the pre-feed, top-of-page, and fuser delivery sensors (PS102, PS103, PS108) are operating and the sensor flags can move freely. We'll be checking this out immediately. Hp 4350 Maintenance Kit Or does the printer not feed the paper from the tray every time?load tray 1, remove paper from tray 2, print something.

Can anyone suggest where I should start looking to diagnose the problem.ThanksPaul by unknown on Oct 10, 2012 at 11:28am Add comment Please sign in to comment That switch is not the power switch. Hp Laserjet 4250 Error Codes Certain control panel messages alternate with instructions about gaining access to the online Help system. The outside plastic and metal frame look the same, but the inner wiring is different. RAM DISK DEVICE FAILURE To clear press Product illustration alternates with The RAM disk had a critical failure and can no longer be used.

CLEANING PAGE ERROR Open rear bin You have attempted to create or process a cleaning page when a duplexer is present and the rear door is closed. Hp 4250 Driver Take it for what it is worth. Remove the toner and look at the image below. Please help!!!

Hp Laserjet 4250 Error Codes

Some non-HP parallel cables might be missing pin connections or might otherwise not conform to the IEEE-1284 specification. original site stacker output accessory. Hp Laserjet 4250 Cleaning Page Contact an HP authorized service or support provider. Hp Laserjet 4250 Manual Use the Device Storage Manager in HP Web Jetadmin to download or delete files and fonts.

After performing the actions above, procede with the following: 1 Turn the printer on. 2 If the error message disappears, reinstall each DIMM and EIO device individually, making sure to turn the printer power off and then on again as you install each device. http://orgias.org/hp-laserjet/hp-laserjet-4000-error-codes.html See Dc controller PCA. 7 Replace the power-supply assembly. The Chinese ones tend to fail quicker. The printer software system is corrupt. Hp 4250 Service Manual

Everytime I tried to set up I get the following error:The HP LaserJet 4250/4350/4240 installation system has experienced a serious mistake and will now quit. I think this prints 55 ppm but now it seems to be printing 25 ppm. by eric111 on Apr 24, 2013 at 4:35pm Add comment Please sign in to comment 0 i just change my fuse abut a month ago, my paper keep getting stuck in the machine, and now it is telling me that i need to change the infuser again, could this be because i am using refill cartridges? have a peek here by stubbs on Jun 19, 2008 at 8:02am Add comment Please sign in to comment 0 What you are missing is you probably did not wait the full 5 minutes after the printer came to ready and then turn the printer off and then back on again and then wait again a full 5 minutes after the printer comes to ready to allow the information from the formatter to write to the dc controller.

Messages are listed in alphabetical order first, with numeric messages at the end of the list. Press and hold down the checkmark (Select) button while the memory is counting. If the defect is not there, the issue is the fuser film.

A jam exists in the staple cartridge (the stapler did not finish stapling but was able to return to its home position). 1 Press ( HELP button for detailed information. 2 Press ( UP ARROW button) and (DOWN ARROW button) to step through the instructions. 3 Remove any jammed paper from the stapler/stacker. 4 Remove the staple cartridge from the stapler unit. 5 Push the green door on the end of the staple cartridge up (in the direction of the arrows). 6 Remove the jammed staple. 7 Close the staple cartridge door.

If the message persists, contact an HP-authorized service or support provider. 64 ERROR For help press Product illustration alternates with 64 ERROR To continue turn off then on A temporary printing error occurred in the scan buffer. Turn the printer power off. See Dc controller PCA. 60.3 Tray 3 lifter motor failure The tray 3 lifter-motor is not functioning. LOAD TRAY XX [TYPE][SIZE] To continue press Product illustration alternates with To use another tray press Product illustration A job is sent that requires a specific type and size that is not available in the tray that is indicated.

Correct the error and then try again to store the job. Replace the connector if it is damaged. 5 Replace the fuser. 6 Replace the dc controller PCA. If the accessory uses cables, disconnect and reconnect them. Check This Out I have HP Laserjet 4240n.

If i disable and enable the printer it starts printing but i have to do this at least 10 times a day. replacing the mains cable but no success. Try removing and reinstalling the optional envelope feeder. If the other scanner assembly solves your problem then I suggest to check your scanner assembly but please be very careful when opening it.

If you believe you purchased a genuine HP supply, go to http://www.hp.com/go/anticounterfeit . We sell High Capacity 20,000 page yield genuine HP 42X Black toner Cartridges Q5942X can be used on HP LaserJet 4350, 4350n, 4350dtn, 4350tn and 4350dtnsl printers. Our 4350 repair team specialize in repairing paper jam error codes on the first visit.. by unknown on Nov 25, 2011 at 12:51pm Add comment Please sign in to comment 0 With the printer turned on and ready, plug the usb cable from the printer into another port on the computer and if the os is windows, the computer should see the printer and automatically load the drivers.

An attempt might have been made to transfer too many macros, soft fonts, or complex graphics. Press Stop. See 500-sheet feeder lifter-drive assembly or 1,500-sheet feeder lifter-drive assembly. 5 Replace the tray 4 feeder controller PCA. The first thing I want to know is there a jam message on the printer when you first turn it on and is it 13.20.