Home > Hp Laserjet > Hp Laserjet 4250 Printer Error Codes

Hp Laserjet 4250 Printer Error Codes

Contents

Re-install the plastic rear output bin. Set the output bin cover aside. Flex the arms on the plastic output bin slightly to remove one side of the tray at a time. That is the source of the KLUNKing noise!I thought:"How can I stop this from happening?" I drilled a small hole through a metal plate and placed a screw that rests just above a plastic part that should have stopped the tray from rising. have a peek at this web-site

As a safety precaution wait 30 minutes for the fuser to cool before proceeding. want to be preparedfor service call 08/07/07 8am. Once you have correct fuser matched up with your model, install the replacement fuser by inserting it and aligning the left side first. If you have any questions give us a call toll-free 866-352-7108 or local 608-831-2396, we can help you get the right fuser for your specific model. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=412144

Hp Laserjet 4250 Troubleshooting

No more KLUNKS. Respond to this 0 http://www.fixyourownprinter.com/forums/printer/43415#1 by moe on Aug 6, 2007 at 5:57pm Add comment Please sign in to comment 0 If your printer is acting like mine; every thing seems to work fine, but once in a while, you hear a KLUNK-KLUNK shortly after the tray is closed and the paper is rising. The outside plastic and metal frame look the same, but the inner wiring is different.

That did the trick! I will forward them to you if you wish. No more 60.02 errors!I took photos but I don't see how to post them here. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 Push the fuser firmly--listen for the sound of both blue levers clicking into place.

Do apprciate any help prior to the morning job. Hp Laserjet 4250n 49.4c02 Service Error Once you have the fuser out, check the fuser's barcode label for the part # and see if the part # matches with your model printer. by istech on May 22, 2008 at 8:03am Add comment Please sign in to comment Bad repair or incorrect info the 60 error would be a lifter motor error.should indicate the tray 2 lifter motor.it would be down on the lower right side.there is a spring that holds tension on top of it.if this comes off,it can cause issues.try switch trays and see if it still comes up.and make sure that tray is fully seated into place.to see the spring ,you would have to take off the right side cover,and i believe the top cover in order to get the right side cover off.could just be an issue with the lifter motor itself. - alam2020 yes my dear i'm also facing the same problem, could u pls help me to giv Next, lower the rear output bin cover as shown below.

The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. Hp Laserjet 4250 Cleaning Page Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations from PrinterTechsGlossary of terms Newsletter Signup Keep up to date with out latesttips, tricks, and products.

wreck 4250 on shelf.

Hp Laserjet 4250n 49.4c02 Service Error

If the fuser does not click into place you run the risk of wearing out both the fuser and the gears that drive the fuser prematurely.

Skip navigation UploadSign inSearch Loading... Hp Laserjet 4250 Troubleshooting On the barcode you will find an HP part #, check the part# on your fuser to see if it matches in the list below. Hp Laserjet 4200 Error Codes While grasping onto both sides of the fuser, push the blue levers upward and pull the fuser straight out.

What isthe likely parts and/or repair. Check This Out The problem is HP makes 3 different fusers which look identical, but the 3 fusers are not interchangeable between printer models. If a duplexer is installed, remove it from the back of the printer. Sometimes a 60.02 error is displayed.Here is how I found my solution. Hp Laserjet 4200 Cartridge Installed Message

PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My Account Checkout Home Troubleshooting 50.5 Fuser Error on LaserJet 4200 4240 4250 4300 4350 Email 50.5 Fuser Error on LaserJet 4200 4240 4250 4300 4350 If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer. If you don't know how to remove the fuser from your printer,it's not difficult -- see the removal instructions farther down the page. I saw that after the tray is closed, the tray sometimes moves up over the gear that turns to raise the paper in place. http://orgias.org/hp-laserjet/hp-laserjet-4250-internal-clock-error.html I took the cover off the power switch side to see what was happening.

Thanks, Hometown Man. Hp 4250 Memory Close Yeah, keep it Undo Close This video is unavailable. If the incorrect fuser goes in, you can get a 50.5 error (or a 13.20 error in some cases) when you power on the printer.