Home > Hp Laserjet > Hp Laserjet 4200 Error E0820180

Hp Laserjet 4200 Error E0820180

Contents

If the message persists print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer control panel and scroll to PRINT CONFIGURATION.) 68.X PERMANENT STORAGE FULL For help press ? top 59.2 MAIN MOTOR ROTATION ERROR Description The printer main motor is not functioning correctly. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions. top 64 PRINTER ERROR For help press? have a peek at this web-site

Figure 28: Closing the rear door If the error persists replace the stapler/stacker or stacker. top 20 INSUFFICIENT MEMORY For help press ? Description The paper that is loaded in the tray is longer or shorter than the size that is configured for the tray. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422

Hp Laserjet 4200 Error Codes

Some Help topics include animations that appear on the control panel to show how to resolve an error. The flag for pre-feed sensor is off center to the left (See Figure 3). If CLEARABLE WARNINGS is set to JOB in the printer configuration menu, these messages are cleared by the next print job. (Click here to see the description of CLEARABLE WARNINGS under "CLEARABLE WARNINGS and AUTO CONTINUE settings" below.) Error messages Error messages communicate that some action must be performed, such as adding paper or clearing a paper jam. Replace the EIO accessory in slot [X].

If jammed, paper is present, remove it. Try printing a job from a different program. Grasp both sides of the paper, and slowly pull the paper out of the printer. (There might be loose toner on the paper. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 Action Turn the printer power off.

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer. WARNING: The fuser is very hot so please be careful. Make sure you have removed the plastic block (with #4 on it) and are pushing down on the #5.

top 49.24.02 PRINTER ERROR Description The printer has experienced a critical error. Hp Laserjet 4250n 49.4c02 Service Error X Description 1- Low fuser temperature 2- Fuser warm-up service 3- Fuser over temperature 4- Line voltage problem 5- Incorrect fuser is installed 6- Open fuser circuit Action Turn the printer power off and then turn the printer power on. Reinstall the cartridge and close the top cover. If done correctly you can typically see the pre-feed sensor flag move when pushing paper up through the path.

Hp Laserjet 4250 Error Codes

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. alternates with 68.X PERMANENT STORAGE FULL To continue press (Select) Description A nonvolatile storage device is full. Hp Laserjet 4200 Error Codes alternates with 59.XY PRINTER ERROR To continue turn off then on 59.2 MAIN MOTOR ROTATION ERROR 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) 60.X PRINTER ERROR 62 NO SYSTEM To continue turn off then on 64 PRINTER ERROR For help press? Hp Laserjet 4200 Cartridge Installed Message If the above action does not solve the issue, contact HP or an authorized service provider.

Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help. Check This Out If the accessory uses cables, disconnect and reconnect them. If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. (Hot water sets toner into fabric.) Figure 3: Removing the jammed paper Open Tray 1 and remove the entrance cover. top 22 EIO X BUFFER OVERFLOW Description Too much data was sent to the enhanced input/output (EIO) card in the specified slot [X]. Hp Laserjet 4200 And 4300 Series Printers Drivers

Slide the tray out of the printer, and remove any damaged paper from the tray. If the above action does not solve the issue, contact HP or authorized service provider. Was the information on this page helpful? http://orgias.org/hp-laserjet/hp-laserjet-4200-error.html Action Turn the printer power off and then turn the printer power on.

The JOB setting determines that the clearable warning message appears until the end of the job that generated the message. 13.20.00 Jam Inside Rear Door Do not tear the paper. top 60.X PRINTER ERROR Description A tray [X] that was opened or filled is trying to lift into position, but there is an obstruction in the tray.

If so, reinstall the duplexer.

Click Here (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00263741) for assistance on removing the fuser. If the above action does not solve the issue, contact HP, or contact an authorized service provider. Print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer control panel and scroll to PRINT CONFIGURATION.) Turn the printer power off. 13.20.00 Jam In Tray 2 NOTE: Do not force the paper if it will not move easily.

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. This causes static electricity, which can cause paper jams. alternates with 68.X PERMENANT STORAGE ERROR To continue press (Select) Description One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to factory default. have a peek here NOTE: Avoid spilling loose toner.

Figure 59: Ensuring the paper is seated correctly Slide the tray completely into the printer.