Scroll to the System Setup submenu, and then scroll to either CLEARABLE WARNINGS or AUTO CONTINUE. Then reboot printer AND computer, reconnect cables, and try printing again. 6. If the message appears only with a certain software program or print job, contact the software vendor for assistance. X Description 1- Low fuser temperature 2- Fuser warm-up service 3- Fuser over temperature 4- Line voltage problem 5- Incorrect fuser is installed 6- Open fuser circuit Action Turn the printer power off and then turn the printer power on. Source
If the error reappears, record the message, and contact HP Customer Support. Press to resume printing. I will have to give their IT the mac address for the new card. Turn the printer off and then on. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422
On EX engine printers this error is caused by a bad PIU (paper input unit). 41.x PRINTER ERROR A temporary printing error has occurred. If the above action does not solve the issue, contact HP or authorized service provider. top 66.12.XX OUTPUT DEVICE FAILURE For help press? Whenever the printer is ready, not busy, and has no pending warning messages, the status message “Ready” is displayed if the printer is online.
If the above action does not solve the issue, contact HP, or contact an authorized service provider. I decided to go ahead and order a jetdirect card as it would be the easiest thing to eliminate. Covered by US Patent. Hp Laserjet 4200 And 4300 Series Printers Drivers Turn the knob to Custom for supported custom paper sizes.
top 13.XX.YY.DUPLEX JOB INTERRUPTED Description There was an error while the printer was duplexing. If the code clears, then power off and put the card into slot 1 and repower on. Make sure the bottom tab on the cover fits into the corresponding slot in the printer. http://www.fixya.com/search/p378590-hp_laserjet_4200_printer/eio_error If it's a networked based printer try the following: Power off machine and unplug power cord.
Chances are you may need to get a new JetDirect Card thoughRyan B. : What is the make/model of your device?JACUSTOMER-99s6rsxu- : Not sure if we're using a JetDirect or not. Hp Laserjet 4250n 49.4c02 Service Error Join the community Back I agree Powerful tools you need, all for free. Loading Tray 2 or an optional 500-sheet tray Remove the tray from the printer. Figure 10: Checking the quality of the inserted paper Slide the tray back into the printer.
Sometimes mismatched software drivers over-inflate the size of a document and cause these errors; you may want to download/install a different driver. If the error persists: 1. Eio 2 Error Hp Laserjet 4100n Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Hp Laserjet 4200 Error Codes Wird geladen...
Insert the HP JetDirect card back into the printer’s EIO slot and ensure that it is firmly seated. http://orgias.org/hp-laserjet/hp-laserjet-4200-error-e0820180.html Replace the network card if needed. 5. All printers pull a reserved ip address from their dhcp server eveytime the network is initialized. Reinstall the cartridge and close the top cover. Hp Laserjet 4200 Cartridge Installed Message
top 13.02, 13.05, 13.20, 13.21 JAM IN TOP COVER AREA Description Paper jam in the top-cover area. Print the Configuration Page. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual . http://orgias.org/hp-laserjet/hp-laserjet-4200-error.html If the issue reoccurs, try installing a known good duplexer from another compatible unit, if possible.
Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. 13.98 Paper Jam If the problem persists when using trays 3 and 4, replace the feed and separation rollers. 2. Action Press the ? (Help) button for detailed information.
Rotate the cover up, toward the printer. If they sold you a 615 card I would never buy from them again. Fanning can cause misfeeds. Eio Accessory All rights reserved.
Action Open the top cover and remove the print cartridge. If the above action does not solve the issue, contact HP or an authorized service provider. Contact a network administrator. NOTE: If the steps listed in this document do not return the printer to a READY state, service may be required. Check This Out If the above action does not solve the issue, contact HP or an authorized service provider.
Figure 27: Removing paper Verify the deflector in the printer is working correctly. Figure 12: Clear the message If the above action does not solve the issue, contact HP, an authorized service provider, or look for the jam in another location. Would not respond to key presses and shows a steady green Ready light. I decided to go ahead and order a jetdirect card as it would be the easiest thing to eliminate.
If the above action does not solve the issue, contact HP or an authorized service provider. Do not tear the paper.