Home > Hp Laserjet > Hp Laserjet 4100tn Error

Hp Laserjet 4100tn Error

Contents

I had never split a laserjet printer before, so I was going slowly and going back and forth to the service manual:http://www.feedroller.com As mentioned, the repair is simple, but does take some time to figure out what you are looking for. by dmzcompute on Feb 14, 2010 at 5:20pm Add comment Please sign in to comment 0 Is this a related issue, i.e. Replace high-voltage Power Supply. Just want to mention that the sticky "L" shaped solenoid arm on the Tray 2 was the problem behind our LaserJet 4100N errors. have a peek here

Replace Formatter PCA. 89 POSTSCRIPT ROM FAILURE 1. Exchange Advertise Here 775 members asked questions and received personalized solutions in the past 7 days. First I tried some felt. When a print job is sent, the arm is attracted to the center of the selenoid by an electrical charge which magnatizes the center of the selenoid. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=83436

Hp Laserjet 4100 Not Printing

Tab missing on top cover. 5. 220V unit plugged into 110V outlet. Having a picture of the arm won't help you at all. by unknown on Sep 10, 2014 at 10:48am Add comment Please sign in to comment 0 Thanks so much for this piece of advice / tutorial. I replaced the thin drum just below the cartridge.I send a job through, "jams", sends out a blank, then I lift the top access panel, shut it again and it will print.Strange.

will check the sensor flag and see what i find , thank you !! If it prints ok from the manual feeder, then the issue is probably the selenoid which controls the movement of the paper tray pickup unit. Respond to this 0 Make sure that the fuser or toner cartridge aren't binding the motor. Optional I/O card is not connected to an active LAN. 3.

Check connector J7 on DC Controller and connector at Fan 2. 2. by blh72 on Jan 6, 2010 at 5:57am Add comment Please sign in to comment 0 You don't mention whether you just cleaned it or put a replacement pad on it like I suggested. Replace Formatter PCA. 64 error 4000/4050/4100/5000/8000/8100 only: A scan buffer occurred - if it persists replace formatter. 66.xx.yy error 4000/4050/4100/5000 only: An error occurred in an external paper handling device, stapler/stacker. 68 RECOVERABLE NVRAM ERROR 1. http://fixyourownprinter.com/posts/22182 Look at your computers first.

II, IID Only: 1. 53 Error - Replace memory card. Replace PostScript ROMs. Learn more You're viewing YouTube in Russian. IIISi/4Si Only: 1.

Hp Laserjet 4100 Manual

No jams no problems. https://www.experts-exchange.com/questions/21900490/Hp-Laser-Jet-4100N-has-an-error-of-EIO-2-ERROR-82-0180-and-will-not-print-PLEASE-HELP.html Reset inteface cable 3. Hp Laserjet 4100 Not Printing Check PS102 and PS103 13.5 Paper delay jam at fuser. Hp Laserjet 4100 Driver On the right side is the drive coupler, which is shaped like a black plastic dumbbell (part# RB1-8877).

So somtimes the "L" arm goes to the center and when power is turned off it stays there sticking with the glue and does not return and stop the paper movement. navigate here If while watching you notice that the paper feeds up an inch or two then moves back a half-inch before feeding into the machine all the way we know we probably have a problem with the black torque limiter in the cassette tray. Join Now For immediate help use Live now! But if I send another print job through, it will give that same error and send out a blank.

Paper path door open. 2. Thanks by unknown on Jan 11, 2012 at 2:33pm Add comment Please sign in to comment 0 dmzcompute,I felt it would've been rather clear as to what my error was, since the title of this thread reads "HP LaserJet 4100 Error (13.1)". by FLOYD on Oct 26, 2007 at 7:26pm Add comment Please sign in to comment 0 I have hp laserjet 4100n printer.when i turn on the printer,it says non hp toner detected.plus when i try to print i get paper jam.when i open the back of the printer,i get the paper that protrudes for roughly 1 cm.i tried many scenarios but failed.any help please. Check This Out If the rollers turn, then on the paper tray itself remove the separation roller and remove the clutch behind it a put the roller back on the tray.

At least one of two tabs must be present. 3. Check tansfer roller. This is when I get the 13.1 paper feed 1.

The printer door/lid is open. 2.

To make sure you replaced the right part, how did you replace the tray 2 pickup assembly. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si Only) 57.1 ERROR 1. All rights reserved. by unknown on Apr 19, 2011 at 8:26pm Add comment Please sign in to comment 0 Thank you so much for this step by step guide.

Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. See picture below -- squeeze the frame below the tab to release the top cover. Personality cartridge installed in font slot is incompatible with printer. 72 SERVICE 1. http://orgias.org/hp-laserjet/hp-laserjet-iip-error-12.html thanks for the cool tip re: sticky solenoid!!!

Not much else it could be except the motor or the cable to it. There is no paper jam and simply opening and closing the top cover will clear the jam. You need something there to keep the plate from sticking whether from residual magnetism or left over goo. Inspect toner level sensor connector for damage. 4.

Join the community of 500,000 technology professionals and ask your questions. Privacy Policy Terms of Use PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My Account Checkout Home Troubleshooting 51.01 51.1 Error HP LaserJet 4100 Laser scanner failure Email 51.01 51.1 Error HP LaserJet 4100 Laser scanner failure  The 51.01 and 51.1 errors are fairly common error codes on the HP LaserJet 4100, 4100N, 4100TN, and 4100DTN series printers.  This error indicates a failure with the laser scanner assembly, which is a high-failure part on these models.  You can try turning the printer on and off; sometimes that will temporarily reset the error code and allow you to print a few more pages.  Usually the error reappears, in which case you should replace the laser scanner.  Fortunately, on this model replacing the laser scanner is not a difficult repair; see instructions below. DC Power Supply malfunction. 2686 Only: 1. IIISi/4Si Only: 1.

Replace if either is bad. 4. Don't replace: rejuvenate! Replace DC controller. My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance?

Try printing from the manual feeder and see if it exhibits the same behavior. Inspect the Fiber Optics Cable for cuts or kinks. 2. Check installation of optional I/O card, reseat if necessary. 2. Visually check or replace toner cartridge. 2.

Replace Laser/Scanning Assembly. 4. Lift the laser scanner straight up and away to remove it.  When you re-install the new laser scanner, be sure the black shutter interlock arm (circled as callout 3 in picture above) is resting on top of the metal shutter plate.  If the metal shutter gets knocked out of place and doesn't open and close properly, it will block the laser beam and you'll get blank print. Disassembled, put on two pieces of electrical tape instead of the felt, reassembled, I still get 13.1.