Home > Hp Laserjet > Hp Laserjet 4100 Error Codes

Hp Laserjet 4100 Error Codes

Contents

Replace Laser/Scanner Assembly. 3. Now turn on the printer and see if you still get the error. We have some broken 610n (J4169) cards, and have new 620n (J7934) and known-working 600n (J3113) cards. Only 2 things that can cause the error are the memory and the formatter.I think you read the troubleshooting wrong. have a peek at this web-site

nope.Do you have any other ideas I can try?Thanks! Also remove the Jet Direct card. See if it starts up that way.If not, (with everything still removed) try a Cold reset. Check Fan 3, replace if necessary. 4000/4050/4100/5000 only: 57.4 Printer Fan 57.7 Duplex Fan 8000/8100 only: 57.2 Fan 3 location: formatter 57.3 Fan 2 location: Low-voltage powersupply 57.5 Fan 1 location: Laser/Scanner 57.6 Fan 4 location: Face down delivery 58.2 ERROR 4100 only: 58.2 An enviromental Thermistor(TH3) failure occurred 58.x ERROR 8000/8100 only: 58.1 Tray 1 lifter malfunction 58.2 Tray 2 lifter malfunction 58.3 Tray 3 lifter malfunction 58.4 Tray 4 lifter malfunction 59.x ERROR 4000/4050/4100/5000/8000/8100 only: 59.0 Main motor error 59.1 Main motor startup error 59.2 main motor rotation error 60-68 SERVICE (II, IID, IIP, IIP+, III, IID, IIIP) 1. this page

Hp Laserjet 4100 Not Printing

IIISi/4Si Only: 1. Please try again later. I work in a library and hate wasting paper. Remove the toner cartridge and look at the image below.

Or if you need year-round support, you can choose our all-inclusive HP LaserJet 4100 annual maintenance agreement.

Common HP LaserJet 4100 (C8049A) Error Codes & Problems HP Error Code:10 - Supplies Memory Error Explanation:Your printer has a problem with the toner cartridge chip, which it's unable to read. The flapper also has a padding glued on which is supposed to stop the clickkng noise of the flapper hitting the center of the selenoid. by unknown on Aug 31, 2006 at 2:44pm Add comment Please sign in to comment 0 Came in one morning and no power to the 4100.Outlet and cord are good. I will call them.

The engine test hole is near the circular vent on the left side of the printer. Hp Laserjet 4100 Manual Reset inteface cable 3. This product has been successfully added to your profile. imp source He loves to get email on the subject. [emailprotected] Anyone tired of all these long threads feel free to email him and ask why the moderator doesn't close them, or if he is able to close them like on other forums.

If the defect is not there the issue is the teflon cover on the fuser and they have a kit to repair that on this site. HP LaserJet 4100 error codes can often help us quickly diagnose your HP printer problems, helping to repair it quickly. Replace Laser Diode Assembly. 3. Bad registration sensor or bad fuser exit sensor.

Hp Laserjet 4100 Manual

IIISi/4Si Only: 1. What would be the advantages?2) If I try to print complex documents in Indesign CS I get a 49.4C06 Service Error. Hp Laserjet 4100 Not Printing Inspect toner level sensor connector for damage. 4. Hp Laserjet 4100 Driver Lift the laser scanner straight up and away to remove it.  When you re-install the new laser scanner, be sure the black shutter interlock arm (circled as callout 3 in picture above) is resting on top of the metal shutter plate.  If the metal shutter gets knocked out of place and doesn't open and close properly, it will block the laser beam and you'll get blank print.

I used the download manager to update the firmware on one of our HP 4100Ns and I am going to watch and see if that fixes it (I've gotten burned in the past with firmware updates so I am going to try updating only one of them to start with). http://orgias.org/hp-laserjet/hp-laserjet-3380-error-codes.html One is to take one of the 4050 formatters and try it in the 4100 it may or may not work. Does it mate with the metal lug on the left hand side of the cartridge?Trev by Trev Pearson on Oct 12, 2005 at 5:20am Add comment Please sign in to comment 1 The following is from the service manual. If after moving the chips, the display is still not on, the formatter they sent you is bad.

Change product Choose from all HP products Enter product serial number Please wait while we process your request. If someone you know has a 4000 series printer can be the 4000, 4050 or 4100 see if you can "borrow" the formatter to try in your printer. When you do a config. Source DC Power Supply/Main motor driver malfunction.

I doubt that is the issue. It's also not a cheap part. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2.

I have removed and reseated the HP DIMMs and restarted the printer with no success.I would appreciated any suggestions.

Check that PS1 is blocked by the latch flag. DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1. by Stephen on Sep 12, 2005 at 7:56pm Add comment Please sign in to comment 0 You might try upgrading the jet direct firmware.The easiest way to do that is to get the Download Manager program from HP, (it's free).It's unlikely that they have 615's installed, those were usually in 4200's, 4300's, and 4600's. Bad fuser bulb. 3.

Listen for scanner motor starting up and LED 003 on DC Controller to illuminate. 3. Replace DC Controller PCA. 57.2 ERROR 1. I/O config for the computer or printer is incorrect. 2. have a peek here HP LaserJet Error Codes and Service errors Back For additional help please Email our technical department Choose the error number from the menu below 02 11 12 12.x 13 13.x 14 16 20 21 22 23 30 40 41 41.x 42 43 49 50 51 52 53 54 54.1 54.4 55 56 57 57.x 57.1 57.2 57.3 57.4 58.2 58.x 59.x 60-68 60,61 62.x 63 64 66.xx.yy 68 69 70-71 72 79 80 89 If you have a Laserjet 4L, 4P, 5P, 6P, 5L, 6L, 1000, 1100, or 1200 and you are getting a light error code feel free to email us for info on the code.
02 WARMING UP (>3 MIN) 1.

by unknown on Nov 10, 2005 at 3:15pm Add comment Please sign in to comment 0 Real easy to remove. The printer door/lid is open. 2. It has 256mg added third party memory. The replacement drives are very very expensive.techtechgirlie,If you remove paper from the paper tray and put paper in the manual tray does it do the same?

I have had this printer since 2002 and it has performed well until just the other day.Now when the printer is turned on, the control panel display shows that the printer is checking the memory. Regards, Andrew” Matthew asked: “ My printer is printing black lines vertically down the page. ” © Teffont Business Systems Limited 2016All Rights Reserved all 3rd party trademarks acknowledged. You will have to replace the main board which I think is the same as the 4100 ecu. a.

You can also take the formatter from the 4100 and put it in one of the 4050 and see it it works. I got the same error with the network card removed. We actually have 2 of these printers in-house and I can "borrow" the formatter. c.

Paper path rollers worn? Replace DC Controller PCA. 3. You may want to try a cold reset to change back to factory defaults. Check transfer guide assembly. 3.