Home > Hp Laserjet > Hp Laserjet 4 22 Par Io Error

Hp Laserjet 4 22 Par Io Error

I was wondering , if the problem was related to the backup software that came with the drive (Seagate backup software v 1.15) if could use another backup utility software to fix the problem. On the IIP/IIIP you can wipe toner/paper dust buildup off the roller and also remove the separation pad (small cork pad) and clean it as well. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. Simplify the print job by removing font changes and/or graphics. have a peek at this web-site

Cleaning may work for the short term but will not solve this problem. If not replace the motor or drive circuit as required. Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. Write the error message and the four digit code down before continuing. http://www.fixyourownprinter.com/posts/22548

This situation may also be encountered during port detection. Back back to top How did we do? Press GO to resume printing. May be feed problem.

On the LJ4/4M/4+/4M+ the sensor flag can get knocked out of place when a paper jam occurs and the tray is pulled out abruptly. Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to resume printing. Mike Posted on Sunday, September 24, 2000 - 2:32 pm: John: THe WM error means that the resource saving memory area is full. How about the I/O port - damaged, seated properly, pins not bent? 4+/5P/5 The computer and printer aren't talking because of improper signal protocols.

Back back to top Error 16 Toner Low Toner cartridge is empty or toner in cartridge is not distributed evenly. Sent via Deja.com http://www.deja.com/ Before you buy. Verify SIMM's are seated properly, replace any defective 5Si 59.X Main motor malfunction X=1: Main motor startup failure, X=2: Main motor rotation failure ERROR 62.X 62.0 Service, 62.1-4 Service, 62.5 Service, 62.6 Service All Printers - SERVICE 1. http://www.verycomputer.com/14_34eeb70694e6cad4_1.htm Defective Tray Size Sensing or Configuration - Most trays have tabs which depress a series of switches when installed.

During the detection process, a signal is sent through the parallel port to be interpreted by the tape or modem device. This is the board mounted to the DC power supply which is in the right front corner of the printer. It won't even print the test document for the computer we attached it to. Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot.

It can also be caused by a defective DC controller. http://www.mj-printers.com/discus/messages/22/1180.html?1168123238 It should not rub off! If,however, you set down at the same machine and logged in as arnold then yourvolume, not mine, would automatically mount without user intervention. The information contained on this chip is dependent on the printer model and the supply.

This is an I/O buffer overrun error. http://orgias.org/hp-laserjet/hp-laserjet-iip-error-12.html HP laserjet 4 plus 22 IO PAR ERROR with EXABYTE internal backup sytem Whenever, Windows 95 boots I receive a 22 IO PAR ERR from my HP Laserjet 4 plus printer, the message appears whenver windows test the Exabyte Eagle TR-3 internal backup sytem. ERROR 89 All Printers (except 5L/6L) The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the proper location and oriented properly This can also be a temporay error, try power cycling the printer The PostScript ROM's/SIMM are defective 8X.YYYY EIO ERROR The EIO accessory card has encountered a critical error. The solution is the replacement of the pickup roller assembly and paper separation pad.

Peachykeen, Dec 1, 2015, in forum: Hardware Replies: 5 Views: 280 lochlomonder Dec 1, 2015 bios problems again oldgadget, Oct 12, 2016 at 3:35 PM, in forum: Hardware Replies: 7 Views: 111 oldgadget Oct 12, 2016 at 5:15 PM All in one PC problems UsbHekp, Oct 7, 2016, in forum: Hardware Replies: 2 Views: 127 UsbHekp Oct 9, 2016 Thread Status: Not open for further replies. Replace if necessary. We also carry a lot Lexmark Toner & Ribbons for your one stop shopping experience. Source PrinterSupplies.com Printer, Copier, Fax Supplies & Parts, since 1992 Customer Service Contact Us Location and Hours Track Orders Website Information About Us Privacy Policy Website Security Info Payment Options Return Policy Sitemap Shipping Information Package Transit Times International/APO Shipping Special Order Items Get Connected Follow us on Twitter Join us on Facebook Join us on Google+ See us on YouTube We Proudly Ship: We Proudly Accept: Credit Card Processing 2005-2014 © PrinterSupplies.com All Rights Reserved.

Can also be caused by a defective DC controller. All rights reserved. Scroll through items until "I/O =" appears and use the +/- key to display parallel and the enter key to select.

Why not 3? 4 Replies 1 View Switch to linear view Disable enhanced parsing Permalink to this page Thread Navigation Darrell Wright 2003-12-01 11:12:27 UTC Michal Jezierski 2003-12-01 11:12:27 UTC Nick 2003-12-01 11:12:28 UTC Stephen L Arnold 2003-12-01 11:12:28 UTC Paul Crittenden 2003-12-01 11:12:28 UTC about - legalese Loading...

Again on the LJII/III we are starting to see more and more failures of the gear drive assembly. A switch on this assembly may not be activated properly. Defective formatter PCA - replace On the HP Laserjet 4/4+/4Si/4V/5/4P/4MP the 53.XY.ZZ error code is decoded as follows: 53 (XY-ZZ) where X- Hardware Type: 0 = ROM 1 = RAM Y - Hardware Device: 0 = On Board RAM/ROM 1 = SIMM Slot one 2 = SIMM Slot two 3 = SIMM Slot three 4 = SIMM Slot four ZZ Error number: 00 = Unsupported memory 01 = Unrecognized memory 02 = Unsupported memory size 03 = Failed RAM test 04 = Exceeded max RAM size 05 = Exceeded max ROM size 06 = Invalid SIMM speed 07 = SIMM reporting incorrect 08 = SIMM RAM parity error 09 = SIMM ROM mapped to an unsupported address 10 = SIMM address conflict 11 = ROM out of bounds 12 = Could not make temporary mapping *A 53.1y08 error is generated in LJ4+ memory is installed in a LJ4 The 53.03.01 error code is decoded as follows: A ROM error in SIMM slot three with unrecognized memory. ERROR 11 - Paper Out (MP/PC/UC/LC/EC/LE LOAD) Paper tray empty or not seated correctly.

Is giving error 421 after works 1 hour. Defective Formatter PCA - Replace with known operational board and try again. Take a look at the white gear - if it looks as if it has twisted on the shaft that is the problem. have a peek here low line voltage causing the power supply circuits to drop out of regulation.

This printer has four lights, Paper Jam, Paper Out, Data, and Online. If not, you may have blown fuses on the DC controller board or a DC controller failure, but in most cases you will need to replace the fuser assembly. Is giving error WM Job 300 after installing new postscript memory. zx10guy replied Oct 18, 2016 at 11:42 AM Loading...

If not, you have the older style filter which requires removal of the top cover to replace the filter. If you don't hear the motor at all, usually accompanied by an error 52 indication, the scanner motor is defective.