Home > Hp Laserjet > Hp Laserjet 2200d Duplexer Error

Hp Laserjet 2200d Duplexer Error

Learn more You're viewing YouTube in German. Best way to test first is to remove the usb cable from the printer. It causes static electricity, which can, in turn, cause paper jams. Turn the printer off and then on. have a peek at this web-site

The paper is feeding down the back toward the back of tray 2 but stops right above it. Replace a DIMM or EIO device if it is the one that has caused the error. Action Remove the printer from any UPS supplies, additional power supplies, or power strips. Use (Up Arrow) or (Down Arrow) to scroll to PRINT CONFIGURATION, and then press (Select). check here

He mentioned that I should check the duplex solenoid first (HP Part No. You have to be careful when doing so that the lubricant doesn't get flung onto the mirrors and lenses. If the printer is on a network, AUTO CONTINUE should probably be set to ON. Push that and it should print a lined test page.

Working carefully it should take an hour. You load the legal paper in tray 2. by dmzcompute on Jun 10, 2007 at 10:05am Add comment Please sign in to comment 0 dmzcompute or anyone else,yeah. The little led piece for the middle light has broken off.

If the problem persists, contact HP Customer Support. I have changed formatters, power boards, Fuser assemblies, Toner cartridges, Paper Trays. Now as to what you say was the issue. http://fixyourownprinter.com/posts/25661 I changed the power cable, just in case...nothing.

Do those lights come on one after the other when the printer is first turned on? reassemble in reverse order.You need a Phillips 2 screwdriver and a flat screwdriver. top 10.XX.YY SUPPLIES MEMORY ERROR Description The printer is unable to read the electronic information (e-label) on the print cartridge so that the printer can keep track of the page count for the print cartridge. When the back edge of the paper enters the printer, open the top cover quickly to stop printing.

If paper is difficult to remove, try clearing it from the tray area. It is not hooked up to a printer by unknown on Jan 20, 2009 at 11:13am Add comment Please sign in to comment I don't know who's more confused, you or me. I took my printer apart and all three of the solenoids had deteriorated foam and glue residue on them. Now I can get this off my bench - life is good.

Then i push the Go and Cancel buttons and the bottom go light goes out. Check This Out Stops inside the fuser, or just exiting the fuser 4.  Stops only when duplexing 5.  Stops as it exits the printer Numeric error codes: Error Codes 0 - 19 Error Codes 20 - 49 Error Codes 50-59 Error Codes 60 and up Text error messages: Error Messages A - E Error Messages F - M Error Messages N - R Error Messages S - Z What area of the printer does the noise seem to be coming from, the front or rear? -- rear noises are usually fuser, drive gears, or output assembly -- front noises are usually pickup rollers, toner cartridges, laser scanners What kind of noise: high-pitched squeals, or low-pitched rumbling? The other place is in the printer memory where it is stored based on old dos commands or plj commands which had been sent to the printer and tell it what size paper is in each tray. Thanks.

Figure 56: Setting the rear guide On the right side of the tray, turn the knob to Standard for LTR (letter), A4, LGL (legal), EXEC (executive), A5, or JIS B5 paper. If a print job is sent and the stapler is jammed or is out of staples, the job will still print as long as the path to the stacker bin is not blocked. Just thick enough to dampen the sound without interfering. Source we have serivce and blower the printer and have clean it through blower, before service the printer print the page with little black print.

This is typically an e-label issue. My next tactic will probably be to take a laptop and plug directly into it and test it.Thanks in advance.Ty by tysonneil on Oct 12, 2007 at 6:32am Add comment Please sign in to comment 0 Hey Ty,Looks like a network connectivity issue. i dont know how well you are with electronics but if you need any help or anything shoot me an email.

CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few minutes.

I did have my hard drive go bad, everything worked fine before that occurred. If not the usb cable is bad and needs to be replaced or the usb output on the computer is bad. The Attention light will come on during this process. 5. Wird geladen...

If possible, try to use a fresh ream of paper and do not fan the paper. Spun it a few times and it broke free. Description The printer received more data than can fit in its available memory. have a peek here Likewise, it has no fax function.

If the motor is frozen these instructions should help.