Home > Hp Deskjet > Hp F2280 Cartridge Error

Hp F2280 Cartridge Error

Contents

Voltage and amperage specifications printed on the power supply Voltage and amperage requirements printed on the HP product In this example, the voltage (+32 V) and the amperage (2000 mA) from the power supply are compatible with the voltage and amperage specified on the HP product. Try the task again. Step five: Align the cartridges Follow these steps to align the cartridges. Figure : Remove the tape If you removed the tape from the cartridge, there is no need to clean the cartridge. have a peek at this web-site

Press and hold the Cancel button (), and then press the Start Copy Color button (). Step two: Print from the application again Try to reproduce the error that caused the blinking lights. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.I am an HP employee. 1 1 Marcusmax Honor Student Posts: 3 Member Since: ‎03-25-2011 Message 3 of 5 (4,083 Views) Report Inappropriate Content Re: Problem with Deskjet All-in-One F2280 Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎03-25-2011 04:45 PM Thanks for that. Disconnect the power cord from the back of the printer.

Hp Deskjet F2280 Reset

Press in the tab on the left side of the rear access door to release the door. Figure : Load the alignment page Close the scanner lid while holding the alignment page in place. Turn on the printer.Step 4Print a test page. We recommend the following software and solutions: Installs and Updates Recommended Solutions to Detected Issues and Errors We have not detected any issues with your product.  You may find a relevant support option by selecting any of the helpful topic tabs on this page or by entering your issue in the above search tool.

Figure : Open the cartridge access door When the carriage stops moving, remove the power cord from the rear of the product. What's New? Solutions Solution one: Reset the All-in-One Follow these steps to reset the product. Hp Deskjet F2280 All Lights On If these steps resolved the issue, there is no need to continue troubleshooting.

Find the blinking lights pattern you are experiencing, and then follow the steps to resolve the issue. Please enter a Product Number to complete the request. Figure : The carriage Figure : The gold-colored contacts in the carriage Wait ten minutes to allow the cartridge and carriage to dry. http://support.hp.com/us-en/document/c00864517 HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading...

You may have to register before you can post: click the register link above to proceed. Hp Deskjet F2280 Manual Thanks for the follow up. The swab should only be slightly damp. Scroll to the bottom of the page, and then make sure the country/region location is correct.

Hp Deskjet F2280 Error Lights

Locate the control panel overlay, and then peel off the paper backing to expose the adhesive. If this is your first visit, be sure to check out the FAQ by clicking the link above. Hp Deskjet F2280 Reset To replace the black ink cartridge, remove the ink cartridge from the right slot. Hp Deskjet F2280 Not Printing Disconnect the power cord from the rear of the product.

Torn pieces of paper from a previous jam are stuck in the product. Check This Out Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. The Size is: window opens. If this happens, press, and then quickly release the Power button () again. Hp Deskjet F2280 Error Code E

Wait until the Power light () stops blinking. Step three: Align the cartridges Follow these steps to align the cartridges. If the ink cartridge is outside of the printer for too long, the ink can dry and clog the nozzles. Source You can also purchase genuine HP cartridges from other retailers. Follow these steps to replace the problem cartridge.

If these steps resolved the issue, you do not need to continue troubleshooting. Hp Deskjet F2280 Troubleshooting Continue to the step to reinstall the cartridge. They are required electrical contacts.

Step two: Test the power on the All-in-One Follow these steps to test the power on the product.

Remove any obstructions found. The carriage moves into the middle of the access area, unless there is an obstruction. Figure : The electrical connections Rear of product Power module Electrical outlet Check to see if the power module has an LED light. Hp F2280 Printer Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray.

Torn, wrinkled, or damp paper loaded in the paper tray. Do not mix different types, weights, or sizes of paper. An obstruction is blocking the paper path. have a peek here Reconnect the power cord to the rear of the product.

Continue to the next step. Open the cartridge access door. Press the Power button () to turn on the product. Do not use paper that is too thin, too thick, or too glossy for the product.

If the computer message is NOT Print Cartridge Error (instead, it says that the cartridge you have removed is ... note: The icon on the USB cable () generally faces up when the cable is connected correctly.