Home > Hp Designjet > Hp T1200 Error Codes

Hp T1200 Error Codes

Contents

Page 46 In the Printhead Information submenu, scroll to the Printhead that you want information on and press OK. Reply 0 0 theasy Honor Student Posts: 4 Member Since: ‎11-30-2014 Message 3 of 7 (1,603 Views) Report Inappropriate Content Re: HP Designjet T1200 79:04 error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎11-20-2014 10:57 AM thanks for your explanations.the printhead carriage is in locked in the parking position. Pro Slate 12) OR Browse all HP products Please wait while we process your request. Change the loaded paper type or the print settings. Check This Out

But it seems there is still another issue. Page 80 Initial This error can occur because the printer has been dropped during transportation, causing structural damage. The printer tests the carriage LEDs and sensors, which may take a few minutes. Do you wish to proceed to the home page of the new product? http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=3941960

Hp Designjet T1200 Service Manual

The following image shows the Power Supply LED, looking through the cover. Then try again to perform the update. When a system error occurs, the printer log may help you to find the cause and the solution. Corrective action Try using a heavier paper type.

Page 160 In the Drop Detector Calibration submenu, scroll to Calibrate Drop Detector and press OK. Page 11: Troubleshooting Paper Jams And Printhead Crashes, Banding At Variable Extreme Environmental Conditions Check the type of paper that is being used since the Line sensor may have problems detecting transparent paper or some types of Non-HP paper. Page 156 The Front Panel prompts you to select the paper category you will use for the calibration. Hp Designjet T770 Troubleshooting Page 96: Appendix C: Obtaining The Printer Log And The Diagnostics Package Appendix C: Obtaining the printer log and the diagnostics package The printer keeps an internal log of its own actions.

For each Printhead, you can see both the adjacent and the consecutive nozzles. Please try again later. Page 70 Warning: 39.1:01 Problem Description: Roll 1 switch failed (standby or resume). Clicking Here Once the paper is unloaded, press OK.

IO warning Try again; if the problem persists, contact HP Support. Hp Designjet T1200 Load Paper Press OK to test the Formatter voltage. All Front Panel keys are disabled while the printer erases the Hard Disk Drive. Page 170: Center Covers (rear) Center Covers (Rear) HP Part Number Part Description Printer Model Cross-reference CH538-67012 Rear Cover All 44-in models Cover, Rear on page 240 CQ305-60015 Rear Cover All 24-in models Cover, Rear on page 240 CH538-67022 Converger Assembly T1200 44 in Converger...

Hp Designjet T1200 Manual

See Customer Self Repair parts on page 182. but when i mark the right quality with the check the plotte doesnot continue to ask for the lenght of the paperroll and the machine just can eject the paper by lifitng the release lever.i already installed the latest version of the firmware and the same error happens again. Hp Designjet T1200 Service Manual Please wait while we process your request. Hp Designjet T1200 Manual Unload Required Some of the problems for which it can help are the following: Troubleshooting area fill uniformity issues such as: ●...

From the Embedded Web Server: go to the Support tab, then select Print quality troubleshooting. In the Service Utilities submenu, select Hard Disk Recovery and press OK. This product has been successfully added to your profile. See Update the firmware. 81:01, 86:01 Please follow the instructions on the front panel. Hp Designjet T1200 Hd Mfp Service Manual

In the Diagnostics menu, scroll to Carriage Assembly and press OK. At the front panel, select the Internal Prints icon, then Service information > Print calibration status. Text messages Message Recommendation [Color] cartridge has expired Replace the cartridge. this contact form Page 29 Make sure that the paper type selected in the Front Panel is the same as the paper type loaded into the printer.

The total memory available in the printer depends on its configuration. Hp T1200 Scanner Manual Taufik RM 4,659 views 3:00 DesignJet 500 firmware upgrade - Duration: 6:39. slowly i bring the plotter back to work.hope you can help me again :-)thanks for now,theasy Reply 0 0 davidzuts Regents Professor Posts: 4,703 Member Since: ‎01-17-2009 Message 6 of 7 (1,557 Views) Report Inappropriate Content Re: HP Designjet T1200 79:04 error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎11-27-2014 08:26 PM Here is what you should do.

Page 28: Lines Are Printed Double Or In Wrong Colors, Lines Are Discontinuous Corrective action The problems may be inherent in the image that you are trying to print.

Find by product name or number (e.g. Continue to hold down all three keys for about 20 seconds, until you see the HP logo on the Front Panel display. Loading... Hp Designjet T795 Service Manual The product could not be added to your profile at this time.

To troubleshoot any displayed error codes, see System Error Codes—Full Descriptions on page The Front Panel shows the test complete display for a few seconds. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Main PCA, see Electronics Module Main PCA and PSU on page 256. *Flashing* Main PCA, see Electronics Module Main PCA and PSU on page 256. navigate here NOTE: If the test on that component/assembly passes, you should not replace it.

Make sure that the paper type selected in the Front Panel is the same as the paper type loaded into the printer. In the Scan Axis submenu, scroll to Scan Axis and press OK to start the test. This will start the printhead alignment procedure. If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services.

Page 143 Enable/Disable Firewall The purpose of this Service Utility is to enable or disable the system firewall. You are recommended to order the Paper Advance Calibration Kit (24-in models: Q6683-60241, 44-in models: Q6687-60093), which contains two sheets of HP Universal Instant-dry Photo Gloss paper. Corrective action: There is no corrective action. Reply 0 Reply 0 0 Everyone's Tags: EBCOMMIPG View All (1) timwj1 Master's Graduate Posts: 475 Member Since: ‎08-11-2010 Message 2 of 7 (1,660 Views) Report Inappropriate Content Re: HP Designjet T1200 79:04 error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎11-14-2014 08:34 AM That error code is almost a catch all code, it pops up when the printer don't know what to do, it states a firmware error but rarely is that the case, sometimes it is a bad hard drive, I have seen a bad electronics module cause it, a bad formatter card cause it, a bad DCHP network setup cause it and bad printheads.If the carriage is not in home position and can be slid out of the service station manually you can access the printheads, the best procedure is to remove all ink cartridges, all printheads, do not plug a network cable in and let the machine boot up, see if the error still exists, if it don't, it is probably one of the printheads causing the problem.

Check your cable connections. Press OK to continue.