Learn more You're viewing YouTube in German. Simply disassemble and clean with lukewarm water in a sink to clean out the ink residue. If no problems are found, or the error re-appears, continue with performing the "D05 Service Station diagnostic test" as listed below. so when the carriage came into the service station it would feel the pressure and would give the error.
Close the Window. 6. Follow the instructions on the Front panel. NOTE: If the carriage does not manually move to the left, DO NOT FORCE IT. Wird geladen... http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/DesignJet-800-Service-Station-21-10-error/td-p/5422315
by SudnDeath on Apr 24, 2006 at 12:25pm Add comment Please sign in to comment 0 I've carried out most of that as mentioned, but unfort. Verify that the cable is not impeding the functionality of the flag. Follow the instructions to perform the update.
Manually move the carriage to the left (out from the Service Station). Wird geladen... If the 21:10 error comes up, you may have a bad service station. Severe Error 0x3010002 align printhead by unknown on Nov 27, 2012 at 6:22pm Add comment Please sign in to comment 0 error 86:01possibly paper jam1.
The Service Station flag should be at about a 45-degree angle as pictured below in Figure 2.Figure 2: Service Station flag correctly positioned If the flag is correctly positioned continue with Step 16. Hp Designjet 500 Error Code 21 10 NOTE: If the printer has been serviced recently, make sure the Service Station nut is installed correctly (new Service Stations C4723-60276 have the nut). NOTE: If you are unable to release the Carriage by the previous process, remove the right end-cover and locate the main Service station gear (as pictured below in Figure 1) and rotate it counter clockwise approximately four revolutions. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0102406 If so something was not done right and the plotter is sensing that door not being shut properly.
b. Hp Designjet 500 Service Station Cleaning It happens more times than you think. Turn the printer on (entering Service mode) and perform the next required calibration. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.
Place it out side & connect it(just for testing connect the unit fron out side).Switch the machine & observe the service station movement..
switch power on5. Hp Designjet 500 Service Station Removal Works like a charm.BySH Gordie Dunlapon June 13, 2014Verified PurchaseA review of the thing that I bought: A service station assembly from HP. Hp Designjet 500 System Error 21 10 check service station cable.If cable is good then go to Interconnect PCA..Chek port & tracks where its coming from(mostly pcb tracks damage found because of age)If tracks are failed replace interconnect PCA.Keep posting...See the PCA tracks: Reply 0 0 zuluzkiller Honor Student Posts: 3 Member Since: 07-18-2011 Message 3 of 8 (477 Views) Report Inappropriate Content Re: DesignJet 800 Service Station 21.10 error Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 12-31-2015 08:36 AM Video does not show it because carriage covers service station in the beginning but if I move carriage manually to another position and power plotter ON there will be bit of movement in the service station but not much.
Transkript Das interaktive Transkript konnte nicht geladen werden. LOL THE BATTLE CONTINUES but i think if i get the HP ink it should fix that problem... Clean and lubricate the rail first. Hewlett-Packard shall not be liable for any direct, indirect, special, incidental or consequential damages in connection with the use of this material. Designjet 800 Service Station
Shipping was fast!Read more0Comment|Was this review helpful to you?YesNoReport abuse5.0 out of 5 starsFive StarsByEurimar Crespoon April 23, 2015Verified PurchaseExcellentRead more0Comment|Was this review helpful to you?YesNoReport abuse5.0 out of 5 starsA review of the thing that I bought: A service station assembly from HP. NOTE: Service Notes Referencing this issue, and the affected serial number range: 2000cp C4703A-05A (ESA0000000 - ESC8A07320), 2500cp C4704A-05A (ESA0000000 - ESC8A18978), 3000cp C4723A-03 (ESA0000000 - ESA8C03538), 3500cp C4724A-03 (ESA0000000 - ESA8C04905). Please add the address to your address book. Just got this designjet 800 from a guy that lost the lid cover of the carriage (blue part LOL) and didn't want to by the whole carriage just for that part so he had it sitting there for a few years, so he told me if i could fix it its mine.
Verify printer functionality by printing several internal prints.Performing service calibrationsFollowing each calibration, turn the printer off to store the new calibration values in the EEROM. Hp Designjet 500 System Error 22 10 NOTE: The printer's current firmware revision must be A.02.04 or higher for a new Service Station to work properly. Melde dich an, um unangemessene Inhalte zu melden.
Wähle deine Sprache aus. If the message "D0500 OK" is displayed the test has passed. Anmelden 29 1 Dieses Video gefällt dir nicht? Hp Designjet 500 Error Codes Melde dich bei YouTube an, damit dein Feedback gezählt wird.
Remember the path does not shutdown until is has to exert more pressue then normal. You might need to have a close observation of the carriage and service station movements, to understand if there is any malfunction.If you are sure that the service station is working perfect, then the next hardware component could be the electronics module. To update the FW follow the next steps (it will ONLY work if the printer is connected via USB to the computer): a. When the plotter was restarted - the 86:01 error came up.
Get fast, free shipping with Amazon Prime Prime members enjoy FREE Two-Day Shipping and exclusive access to music, movies, TV shows, original audio series, and Kindle books. > Get started Your Recently Viewed Items and Featured Recommendations › View or edit your browsing history After viewing product detail pages, look here to find an easy way to navigate back to pages you are interested in. the next mistake is i got that remanufactured ink cuz i didn't know if was gonna work so i didn't buy the good ink... So i think i got start up print heads for nothing LOL oh well. I did get 22.10 error when trying calibration but after fiddling with ink/ink supply stationand cable that was resolved as well.
If problems were detected and rectified in the steps above test printer functionality. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen. Anmelden 1 Wird geladen...
If any rejection of PHs appears while replacing them or if the printer is unable to finish the PH alignment, then the expired PHs need to be replaced with new ones in warranty. Hinzufügen Möchtest du dieses Video später noch einmal ansehen?