System error 55:11 A problem with the line sensor has occurred. Click here to download HP drivers and/or software . top System error 08:11 Explanation The front panel cannot be detected. top System error 87:13 Explanation Unable to read the carriage encoder sensor. http://orgias.org/hp-designjet/hp-printer-error-code-79-04.html
Following a successful troubleshooting plot, internal printer functionality has been verified. ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card). If the error code appears again, check the printhead alignment print. Remove the formatter card and re-install the formatter card. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00993566
Plug the power cable in, turn the printer on and attempt to verify functionality. Plug in the power cable again and check to see if the error code has disappeared. Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 500 Error 79 04 Was the information on this page helpful?
Continuable and non-continuable HP DesignJet error codes Some HP 500 error codes are continual, which means that it is possible to press the Enter key on the front panel and to continue working with the printer. Hp Designjet 800 System Error 05 10 General information with more detailed information available. Before calling one of the Hewlett-Packard offices, please have the following information available to help them quickly answer questions: The printer product number and the serial number, found on the label at the back of the printer. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00805065&sp4ts.oid=61000 If the problem persists, click on Support at the top of the page for additional HP support and contact options.
If the error code reappears, upgrade the firmware. Hp Designjet 500 System Error 81 01 Verify SIMM's are seated properly, replace any defective 5Si 59.X Main motor malfunciton X=1: Main motor startup failure, X=2: Main motor rotation 59.XY 4200/4300 Series Main motor failure, check wiring harness Replace main motor, replace DC controller PCA 59.A or 59.4 EP Motor Failure - Replace print cartridge motor (LJ 4300 ONLY) failure Back ERROR 60.2 Tray2 Lifter Motor Not Functioning Power cycle the printer (OFF/ON) Verify that the tray 2 lifter wire-harness is full seated in its connector on the dc controller PCA Replace Tray 2 lifter drive assembly Replace DC controller PCA Back ERROR 62.X 62.0 Service, 62.1-4 Service, 62.5 Service, 62.6 Service All Printers 1. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. HP 500 System error 01:12 The EEROM is not configured correctly.
top 273:00 warning code Explanation Yellow Printhead Error. Remove and re-seat the network card. Hp Designjet 800 Formatter Card Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 500 Error Codes top System error 05:09 (only applicable for Designjet 500 series) Explanation Formatter installed instead of HP-GL/2 accessory card.
Depending on the model, a firmware DIMM may need replacing or a flash update. http://orgias.org/hp-designjet/hp-printer-system-error-21-10.html The product was delivered just a few minutes ago. Replace as needed IIP S/N between 2925J00000 and 3047J99999 replace fuser assembly Back back to top How did we do? Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over the oblique roller cover. Hp Designjet 500 Error Code 21 10
NOTE: Three sources of information are readily available to help you find an HP Support Services phone number: NOTE: 1. Click here for information on contacting HP Customer Care. Plug in the power cable again and check to see if the error code has disappeared. Check This Out System error 64:03 USB port communication problem.
We got it this morning and I have it installed. Hp Designjet 510 Error Codes After installing a maintenance kit, reset the maintenance count to zero by: 1. So the problem must be with Fire -fox and printer interface?
Also verify the configuration through the menus on the printer. Plug in the power cable again and try the printhead alignment again. Click here for information on how to upgrade the printer's firmware. Hp Designjet 500 Firmware Update Download If your machine uses a paper separation pad, a small rubber or cork material pad check for a smooth surface without any friction.
top System error 55:11 Explanation A problem with the line sensor has occurred. If the error occurred while trying to access the IO Menu, then there is a solution : just upgrade to firmware A.02.08 , which in fact solves this problem. Figure 2: Printer Information page one top Understanding the front panel error code display System error codes are displayed on the printer's front panel, using the lit or flashing Ink Cartridge icon bars (see the figure below). this contact form To check for the latest firmware updates for your printer using the HP website, go to HP Support Center .
Call HP for telephone support We offer telephone support for most Hewlett-Packard products. Reseat the EIO card in slot corresponding to [X]. 3. We replace HP LaserJet printer maintenance kits and fuser kits and clear printer maintenance service error message! Are you having problems with the printer or just curious?