Home > Hp Designjet > Hp Designjet 2500cp System Error

Hp Designjet 2500cp System Error

Install the Firmware SIMM and PostScript SIMM in the correct slots Remember that the Firmware SIMM (including the firmware code for the imaging and UV Durable Inks) must installed in the first slot from the left. The system returned: (22) Invalid argument The remote host or network may be down. Check Refill Stepper Motor and Sensor cables. If you have an error code that does not appear here you may have to contact your local HP service center. have a peek at this web-site

Replace the Line Sensor. Perform the Line Sensor calibration » page 5-10. 4 The Line Sensor is installed incorrectly. If Bail Assembly is NOT raised, test has failed - Replace Bail stepper motor. If it is too close it can cause media jams between the leading edges of the media and the Media Separator. 6 Did the failure occur at the end of the media roll? • There are two known failure modes in this case.

Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew ZealandÖsterreichParaguayPerúPolskaPortugalPuerto RicoSchweizSouth AfricaSuisseTürkiyeUnited KingdomUnited StatesUruguayVenezuelaΕλλάδαРоссия中国台灣日本香港대한민국End of Country / Region Selector contentAmericasAsia and OceaniaEurope, Middle East and AfricaClose Country / Region Selector Dialog About usAbout usAbout usContact HPCareersInvestor relationsSustainabilityNewsroomAccessibility Ways to buyWays to buyShop onlineStore locatorCall an HP repFind a resellerEnterprise Store loginPublic sector purchasing SupportSupportSupportDownload driversSupport & troubleshootingForumsRegister your productManage commercial support casesAuthorized service providersCheck repair statusTraining & certification HP PartnersHP PartnersHP Partner First programPartner portal Stay connectedStay connected Sign up for news & offersSign up for news & offersSubmit Recalls|Product recycling|CA Supply Chains Act|Site map|Privacy|Terms of Use|Cookies & ad choices|Limited warranty statement|Terms & conditions of sales & service© Copyright 2016 HP Development Company, L.P. Recommended Action Turn the printer off, then on. Figure 2: Rubber tab on left side of the overdrive assembly (HP Designjet 750c pictured) If the tab was re-positioned in the previous step, turn the printer on and attempt to verify functionality.

System Error: Problem Description: Corrective Action: 010034 000X0000 One of the DC Motors has failed. Hewlett-Packard shall not be liable for any direct, indirect, special, incidental or consequential damages in connection with the use of this material. Web computercare.cc Save Big on OEM New, Remanufactured and Compatible Ink, Ribbons and toners for Printers, Plotters and Postage Machines DesignJet Plotter RepairRepair Tips for DesignJet Plotters Tech TipsPlotter FixLJ RepairTech Links HomeLog in Find admin07/26/05 Error Codes for DesignJet 2000CP, 2500CP, 3000CP, 3500CP Link: http://www.computercareonline.com/designjet-parts-by-model-c-67.htmlTweetDesignJet Plotters can tell you alot if you know what to look for. Service Station 5-11 C05. top System error 010023 Explanation A fuse on the main PCA has blown.

System Error Codes HP DesignJet CP Series Printers 2-3 System Error: 010021 AXXXXXXX Problem Description: The base DRAM or the RAM SIMM tests failed. If "D0300 OK" - Test Passed. Corrective Action: Try the foil owing: • Switch the Printer OFF from the back and then disconnect theTrailing Cablefromthe Electronics Module. here If the carriage does not pick up the Cutter Assembly, test has failed - Check if the Cutter has been disabled through the front-panel (Device Setup / Cutter).

Re-install the SIMM cover. But, we will try and help you avoid that. Remove the Drive Roller and install in the correct position. "Switch Power Off / Check Printhead Path" message appears when the Printer is about to cut or is cutting? The other is with Coated Media, where some rolls have the final edge of the media bent in a "C" shape which could cause a head crash when passing under the carriage.

System Error: 0000D8 - Refer to System Error Code 07xxxx. http://fixyourownprinter.com/posts/22887 Error data: 00000800 -* Problem with the Y-axis. 00001000 -* Problem with the X-axis. Reposition tab(s) as needed. Please try the request again.

A -» Elevator Stepper Motor Failed. Check This Out Using this procedure you will be able to determine exactly which component failed. Wait until the message "F I ash Programmer l.X / Push to continue" is displayed on the front-panel before releasing the CANCEL key. 3 Press the Down Arrow key and the message "Program Flash /Copy to 2nd Flash" is displayed on the front-panel. 4 Press the Up Arrow key and the message "Program 2nd Flash / Program 1st Flash" is displayed on the front-panel. 5 Press the Down Arrow key and the message "Really Erase Yes / 1st Flash? H— *•* U*ri II P»0UMrf^ 1 Uni e^rf — I l-^-l ■ WtaFWiw M «bvWi^ ■ frwrtmjtui A&A.1MB 1 IH fcnlhl Hf "■" !

Scroll to D05 Service Station and press Enter. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett- Packard Company. Try the foil owing: • M ake sure that both DC M otors are connected correctly. • If the error code is related tothe Y-axis motor: • Make sure that the Refill Interconnect Cable (the black cable that connects the Refill Assembly to the Electronics Module) is correctly connected tothe Electronics Module. • Replace the Refill Interconnect PCA » page 8-64. • Replace the Y-axis Motor Assembly | Page 8-45. • I f the error code i s rel ated to the X-axi s M otor, replace the X-axis Motor Assembly t Page 8-66. • If both DC Motors fail, replace the Electronics Module I page 8-6. Source Recommended Action Open the printer's top cover.

If all the keys are pressed and the test passes, "D0700 OK" is displayed. The product could not be added to your profile at this time. Bail Purpose - Test the Bail Assembly.

Perform the Refill Calibration t page 5-9 and try to load the media again. • The refill station positioning must be checked afterwards since it is affected.

Working with refill problems General tips: • Check media type is loaded correctly. • Check refill type is set to default. • Try a higher image quality setting for better performance. • Check user's expectations - refill performance is not always "perfect", but almost always is acceptable for poster-type applications. This short circuit is causing some of the fuses in the Electronics Moduleto burn. If "D0301 Fail", "D0302 Fail" or "D0303 Fail" - Apply lubricant to the slider rods. Try to reinstall it and make sure that it is connected and seated correctly.

If "Green OK V: ##.## / Blue OK V: ##.##" - Test Passed. Clean the drive-roller » page 9-3. 1-12 HP DesignJet CP Series Printers Troubleshooting 2 The lens cover, which is installed on the line sensor, is dirty. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. have a peek here Recommended Action Turn the printer off, then on.