Home > Fuser Error > Hp Laserjet 4100 Fuser Error

Hp Laserjet 4100 Fuser Error


RE: fuser error with a good fuser mufka (ISP) (OP) 6 Jan 10 11:08 Just to clarify, I checked the two fuses on the ECU.Those are the ones we are talking about, right?Perhaps these components are called by different names, but I'm calling the ECU (ECB) the board that is sandwiched in the middle of the printer. kit. If the heater control does not send a signal to activate the heating in the fuser it will also generate the 50.2 error if a thermistor is blown.ECU schematics -> http://www.countryfisher.com/images/temp/ecu.jpghttp://www.countryfisher.com/images/temp/ecu2.jpg RE: fuser error with a good fuser mufka (ISP) (OP) 5 Jan 10 13:17 I assume that replacing the ECB would likely fix the problem.Am I correct? If the message persists, reseat  the Fuser. Source

I've probably worked on over a thousand of these models and only once did I have to replace a engine control board in a 4100 to fix a fuser error. Anmelden 1 Wird geladen... These machines draw a lot of power so they should never be plugged into a power strip with other devices, battery back up, and make sure there are no other large equipment or heater type products on the same circuit. Melde dich bei YouTube an, damit dein Feedback gezählt wird.

50.2 Fuser Error Laserjet Pro 400

or it's affiliates. All rights reserved.Unauthorized reproduction or linking forbidden without expressed written permission. Regards, Phil http://www4.itrc.hp.com/service/jame...75426+28353475 Reply With Quote 11-29-2006,03:10 PM #3 Scline30 View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Nov 2006 Posts 2 Thanks I had tried most of the suggestions there, but thanks. The fuser  is very easy to replace and no tools are necessary on the HP 4100 and only a phillips screw driver on the 4000 and 4050.HP Laserjet  4000, 4050, and 4100 Fuser RemovalNote: Unplug power and communication cables and allow at least 10 minutes for cool down before fuser removal. 1a. 4100 - Facing the rear of the printer, press the left side (formatter side) of the rear output bin and release the hinge from the slot. 1b. 4000 - Facing the rear of the printer, pinch the right side of the Rear Output Bin and release the hinge from the slot. 1c. 4000 - remove the Left and Right Duplex Access Covers from the rear of the printer by pulling each from the bottom. 2.

RE: fuser error with a good fuser hpwizzard (IS/IT--Management) 5 Jan 10 05:07 If the fuses are OK we must assume the power supply for the fuser is good and then the isssue would be located on the engine controller board where the fuser heater control is. Corporal: An expert that has over 10 points. Posted on May 21, 2012 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great answer: - Answer the question. - If you need clarification, ask it in the comment box above. - Better answers use proper spelling and grammar. - Provide details, support with references or personal experience. 50.2 Fuser Error P4015 RE: fuser error with a good fuser mufka (ISP) (OP) 4 Jan 10 18:31 Fuses are ok.

Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations from PrinterTechsGlossary of terms Home Site Map Policies Legal Back To Top © 2016 PrinterTechs.com Inc., PrinterTechs and the PrinterTechs logo are trademarks of Printertechs.com, Inc. Fuser Error Hp Printer If the problem is not related to the Fuser, replace the Engine Controller Board Conclusion About the HP Laserjet 4000, 4050, and 4100 50.1 Fuser Error MessageYeah, there are ways to check the OHM readings on the fuser  thermistors  but replacing the heating element will only save you a few bucks than replacing the whole fuser  so I'm not going to go into detail other than what's above. I want to thank you for your fast reply. navigate here If there is no continuity between the Fuser connectors J143F (neutral) and J142F (hot) with the Fuser removed, replace the Fuser. 4.

HP 4000/4050 Fuser Assembly RG5-2661-000 HP Fuser for LaserJet 4100 4000/4050 FuserPrice: $60.00 (0 customer reviews)10 used & new available from $45.00

HP Fuser for LaserJet 4100Price: $99.99 (5 customer reviews)6 used & new available from $99.99

HP LaserJet P3015dn Printer - Black/Silver - CE528APrice: $887.00 (129 customer reviews)63 used & new available from $139.99

HP Laserjet Ent 600 M602N PrinterPrice: $1,699.99 (76 customer reviews)31 used & new available from $379.00

HP Laserjet Ent 600 M602DN PrinterPrice: $1,400.34 (12 customer reviews)21 used & new available from $453.01

All the information on this site is free. 50.3 Fuser Error The guy or girl  who read that and found it intresting hasn't been laid for awhile.   I put that in there just in case your machine is having odd issues and actual replacement of the fuser didn't solve your problem. Last thing to try is leaving the machine unplugged for 10 to 20 minutes and then plug back in and try again which is what HP recommends in the service manual and what any tech or service company would say if you were to call and ask for some advice.Advanced Troubleshooting for the HP Laserjet 50.2 Fuser Error in a 4000, 4050, and 41001. Contributor 12 Answers Re: i have a 50.2 fuser error.

Fuser Error Hp Printer

Wird geladen... That ECB.....is it the board mounted on the riser near the RAM and IO ports ? 50.2 Fuser Error Laserjet Pro 400 Then flip the fuser over to the right side (the non-gear side) and press in on the other fuser tab to make sure it is also fully clicked in place. (right side of a LaserJet 4000/4050 fuser pictured below) (right side of a LaserJet 4100 fuser pictured below) After pressing in on the tabs, re-install the fuser and test.  If the '50.2' error continues, replace the fuser. 50.2 Fuser Error Hp 4525 Under the instructions to replace the fuser  is a link to purchase a fuser.

Trev by Trev Pearson on Dec 15, 2004 at 11:44am Add comment Please sign in to comment 0 Brian, Trev, First ... http://orgias.org/fuser-error/hp-laserjet-4100n-fuser-error.html Comment Flag More Print this page Share this page × Moderate Help this question get an answer Is this question mis-categorized or about a different product? I've tried the 1st fuser in another printer...working fine ! Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place, as shown below. What Is Fuser In Printer

Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. What does that mean It seems that the fuser is not getting hot. Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... have a peek here PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My Account Checkout Home Troubleshooting 50.2 fuser error HP LaserJet 4000 4050 4100 4200 4300 Email Loose fuser tabs on the HP LaserJet 4000, 4050, 4100, 4200, 4300 - a potential 50.2 error If you are experiencing a "50.2" fuser error, first turn the printer off and back on.  Sometimes the error will temporarily go away with a reboot so you can print a few more pages, but usually the error reappears.  If you recently moved the printer around or if you recently installed a new fuser, particularly on HP LaserJet 4000, 4050, 4100, 4200, or 4300 series printers, you should check to see if two tabs on the fuser have come loose. (They can get dislodged during shipping, heavy movement, or during fuser installation.)  See more info below on these tabs.

Join your peers on the Internet's largest technical computer professional community.It's easy to join and it's free. 50.1 Fuser Error This content is provided “AS IS” and is subject to change or removal at any time. Brian by Brian on Dec 15, 2004 at 7:05am Add comment Please sign in to comment 0 Thanks for your hint !

Expert 59 Answers Re: i have a 50.2 fuser error.

Please - what means the message "50 service " on the panel ? Someone suggested the main board replacement, but it's expensive, is it worth it? Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. 50.2 Fuser Error 4200 Something just didn't go as planned and the machine never reached its correct temperature needed to start the printing process.

or its affiliates. If the problem is not related to the Fuser, replace the Engine Controller Board Conclusion About the  HP Laserjet 4000, 4050, and 4100 50.2 Fuser Error MessageYeah, that last  section was boring. What's New? Check This Out It takes a lot of time and effort to put these articles together.

Replacement kit available here for about $40. Flip it to the gear side (the left side) and press inwards on the fuser tab to make sure it is fully clicked in place, as shown below. First Time Here? It can be due to a bad fuser bulb, connections, or the power supply.Reset the machine by leaving the power off for at least 15 minutes, if the error comes back after turning the printer on, you have parts that need to be replaced.call an expert from HP to replace the parts :) Sep 26, 2008 | Printers & Copiers 2 Answers Fuser Error 50.1 Fuser is hot.

Tried all ways of going around it but failed . Wird geladen... Anmelden Teilen Mehr Melden Möchtest du dieses Video melden?