Home > Error Codes > Hydro Quip Error Codes

Hydro Quip Error Codes

Contents

Support: Balboa topside displays OH or OHS 54. Gecko Error Codes (new style)/ Hydro-Quip Error Codes 32 Degrees ~ Temp Sensor not detected. 112 Degrees Flashing ~ Water too hot, let cool down & system will reset itself to 109 Degrees. 3 Flashing dots (display) ~ Water flow problem check for closed valves, dirty filters, water level, pump/wet end operation/defective pressure switch. Support: On an initial installation of a motor why does the motor run momentarily then stop? 42. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection to 0.0.0.7 failed. weblink

Support: Wiring information for the (15-350-4015) Exec-48 1.5HP 110V WaterWay pump, 2.5" Intake, 342061A-13 102. Heater disabled but the spa is operational.SESH = Sensor short, nonfunctional. Support: Blower stopped working or burnt. 16. All trademarks are the property of their respective trademark holders. © Copyright 2005-2016 by Spas2order.com, SpaGuts and New Guts for Old Spas are registered trademarks of Spas2order.com. navigate to these guys

Hot Tub Error Codes

COL = Cool condition. Payment Information via cashier's check or money order 139. Why does the motor run in high speed in circulation and heating mode? 36. Generated Tue, 18 Oct 2016 03:24:24 GMT by s_wx1127 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.8/ Connection to 0.0.0.8 failed.

Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Are your spa ozone units rated for koi ponds and aquariums? 137. Support: Wiring information on the (15-350-2170) 48-Frame 2.0HP 220V CD WaterWay Pump, 342102A-15. 96. Vita Spa Error Codes OHS = Overheat.

Support: Topside installation for the CS-Series and M-Series Electronic Spa Controllers 46. Balboa Hot Tub Error Codes Support: How to install a new replacement temperature sensor on the Electronic Controller. 69. Brett Spa Side Error Codes OH : Temp exceeds 118 degrees Fr : Freeze condition - temp below 40 degrees FL : Pressure switch failure EO : Shorted temp sensor E1 : Open temp sensor E2 : Shorted hi-limit sensor E3 : Open hi-limit sensor E4 : Shorted flow switch E7 : Improper electrical connection For more information Regarding Brett Aqualine tech support click here Hercules Spa Side Error Codes OH : Spa temp exceeds acceptable limits FLO : Flow problem ICE : Freeze condition detected SN1 : Hi-limit sensor failure SN2 : Temp sensor failure ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. http://www.spaspecialist.com/vistasilverpanel.html Support: Small white wire in a plastic sleeve on the back of the VS Series Controller Box 129.

SEoP = Sensor open or disconnected. Hydroquip Spa Systems Check the condition of the filters. PSoH = Pressure switch open with high pump. NOTE: After the unit cools down below 115ºF, the Freeze Protection Circuit can automatically engage if needed.

Balboa Hot Tub Error Codes

Will your blower work on 50Hz? 145. http://www.spapartsshop.com/spasideandtopsideerrorcodes.aspx If you get an error code and the pump is not running when it should be on, check the fuses on the circuit board. Hot Tub Error Codes Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? 1-877-772-7801 M-F 9am-6pm est Sign up Now! Hydroquip Spa Troubleshooting Support: Water leaking from pump unions or heater split nuts. 8.

Support: Smart Winter Mode on Gecko Systems and CS Series 44. http://orgias.org/error-codes/hresult-error-codes.html It is recommended that the system is powered up at a time when the programmed cycles do not interfere with sleeping hours. Support: SpaGuts VS Series Topside Panels are not responding. 130. Support: Freeze Protection on Balboa M7 Systems 125. Hydroquip Hq6000

When you set the filter cycles the main jet pump will come on and run for 8 minutes then goes off and the circ pump will continue to filter the water. Can I use Salt with a SpaGuts or Balboa brand Spa Controllers? 149. Flashing dots & Lit light on display ~ Hi-limit trip, reset power to clear. check over here Please try the request again.

Do not use spa when temperature is flashing or the OH message is displayed. Marquis Spa Error Codes Depending on where the temp sensor is mounted; usually in the wall of the spa in a sensor mount, you could have a flow issue. Support: The VS Series Control System is coming on too much, and may not be normal. 126.

Support: Why does the light on my ozonator stay on all the time on the SpaGuts CS-Series? 38.

Support: What is the maximum water temperature the bathtub heater will heat up to? 117. Spa Builders Spa Side Error Codes Sn1 = Nonfunctional high temperature sensor. Water temperature has reached 118ºF. Gecko Spa Pack Error Codes A second press will turn if off.

Support: Temperature display is flashing on the Electronic Topside Keypad. 45. Temp reads correct water temp ~ Good; if incorrect replace sensor. Will 208V supply be OK for a Spa Pack rated at 240V? 150. http://orgias.org/error-codes/hp-msl2024-error-codes.html The first press of the Auxiliary will turn it on.

Support: Balboa topside displaying (SnA or Sa) 51. System will restart when temp. Spa has shut down. I have you guys bookmarked now for all my hot tub needs and will be referring others to ur site because of ur prompt service and very reasonable prices." - Sarah Jane Polk, Little Rock, AR "I just wanted to leave a testimonial..!