Home > Error Codes > Hp Tape Library Error Codes

Hp Tape Library Error Codes

Contents

When you press Enter, the OCP displays the error message, as shown in Error message in the OCP Error Log (Figure 6). If the failure remains with the same slot, the magazine is probably at fault. Refer to the manuals supplied with the other devices on the SCSI bus for information on enabling or disabling termination on those devices. If you are unsure of the speed of the HBA or switch that the Library is connected to, try Automatic (on the RMI) or Auto Detect (on the OCP) option. Check This Out

Clean the tape drive. top Service and repair Releasing the magazines manually If you cannot remove the magazines via the OCP or RMI, do the following: Unplug the power cord from the device. If other tapes are still in the device, or if it is unable to manually remove the magazines and drive, contact HP service for further instructions. The main error code (0x83) is displayed in parenthesis as the Global error code. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00574301

He Cannot Initialize Barcode Reader Code 80 01

This is most likely caused by a dirty drive that cannot read a tape and marks the tape invalid. Verify that your HBA is supported by the host computer and qualified with the Autoloader. In Services, right-click Removable Storage and select Stop. The Autoloader was unable to complete the requested operation with the selected tape cartridge.

The text description in the header (robotic controller error in this example) is the simple text description of the main error code. Use the magazine removal process to release the magazine and remove it from the device. Unless otherwise noted in the Troubleshooting table , try to resolve the error by cycling power to the library and retrying the last operation. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report Finding error code information on the OCP When an error first occurs, the error message and error code are displayed on the OCP, as shown in Initial OCP error message (Figure 4).

Run the wellness test. 8E Ends of gripper movement not in expected range Run the wellness test 8F Ends of slider movement not in expected range Early firmware versions were not able to use as much force to get or place media in a magazine. Msl4048 Error Codes An Ultra 160 connection is barely adequate for an Ultrium 920 tape drive. Are you sure you want to continue?CANCELOKWe've moved you to where you read on your other device.Get the full title to continueGet the full title to continue reading from where you left off, or restart the preview.Restart previewscribd HP StorageWorks 1/8 G2 Tape Autoloader - TroubleshootingDocument ID:   n/aCreated:   n/aUpdated:   n/a Overview SCSI installation problems SAS installation problems Operation problems Performance problems Average file size File system type Connection from the host server to the disks Operating system configuration Windows Novell Backup server Backup type File-by-file with a full-featured backup application File-by-file with a native application Disk image, flash, or sequential Database backup Connection from the host server to the Autoloader Media Service and repair Removing stuck tapes from slots Releasing the magazines manually Error codes Finding error code information on the OCP Finding error code information on the RMI Finding error code information on an L&TT support ticket or report Main error code descriptions Drive error codes Error sub-code descriptions Robotic error sub-codes Device error sub-codes Warning events Using HP Library & Tape Tools to diagnose problems Overview This document contains information about various troubleshooting procedures for the HP StorageWorks 1/8 G2 Tape Autoloader. his explanation Parallel SCSI: Ultra 160 LTO-2: GOOD.

If there is a tape in a drive, replace the magazines and run the Force Tape Eject operation. Ibm Ts3100 Tape Library Error Codes The text after the main error code (Robotic controller generic problem in this example) is the text description for the error code. Tape stuck in storage slot. top SAS installation problems Problems encountered after installation are often caused by improper SAS cable connections, application software configuration errors, or an incorrectly configured operating system.

Msl4048 Error Codes

If the failure follows the tape cartridge, the tape cartridge may be at fault. Check your software provider's website for the latest drivers and patches. He Cannot Initialize Barcode Reader Code 80 01 Device error sub-codes Error code Description 81 Drive wake up failed 88 Error accessing slot status 90 Robotic load not reached Cartridge Present sensor 91 No activity after Load command 92 Time-out while loading tape 93 No activity after load command 94 Time-out drive Unload 95 Drive terminated unsuccessfully 96 Tape not ejected at robot unload 97 Slot not free at robot unload top top Drive error codes The drive error codes are displayed on the RMI drive status page. He Slider Blocked Error During Second Slider Movement Code 8a 63 During the inventory process, the bar code reader attempts to read the bar code on the cartridge or the bar code on the back of the storage slot until it identifies the cartridge or determines that the slot is empty.

B0 Command from Library controller to robotics controller did not complete in time allotted Reset the device and retry the operation. http://orgias.org/error-codes/hresult-error-codes.html Ultra Wide and Fast Wide are inadequate transport mechanism for Ultrium tape drives. Remove the tapes that were marked with !. Ultra 160 is a good transport medium, but does not have enough bandwidth for LTO-3 or LTO-4 tape drives. He Sled Position Not Found Code 9b 37

LTO-3: GOOD. Third code - the sub-code (62 in this example). Elevator: The part of the robotics assembly that moves in the vertical direction. this contact form top Detection problems after installing a SAS device Problems encountered after installation are often caused by improper SAS cable connections, application software configuration errors, or an incorrectly configured operating system.

Slider: The part of the robotics assembly that plunges in and out for get and put operations. Msl2024 top Detection problems after installing a parallel SCSI device Problems encountered after installation are often caused by improper parallel SCSI bus configuration, application software configuration errors, or an incorrectly configured operating system. If the screen shows Logged Out: Check that the Fibre speed is set to Automatic (on the RMI) or Auto Detect (on the OCP), or that the correct fibre speed is selected.

CAUTION: Shipping Lock: The shipping lock must be removed for the robotics to work properly.

top top Error codes If an error occurs during operation of the device, the device stops the current operation and displays an error code on the LCD screen. The bus would be saturated when providing 2:1 compressible data to an Ultrium 1760 tape drive. F4 Time allotted for drive loading exceeded Check that the tape cartridge is supported and has not exceeded its usage life. If the problem continues, contact HP customer support.

The reader can usually identify a properly-labeled cartridge the first time, while determining that an unlabeled cartridge is in a storage slot can take four times as long. SCSI Cabling: Verify that all SCSI cables are securely connected on both ends. The date is in the format year/month/day. http://orgias.org/error-codes/hp-msl2024-error-codes.html Check the SCSI connector and terminator for bent pins.

It can be downloaded free of charge from http://www.hp.com/support/TapeTools . Try the following steps, in this order, to remove the stuck tape. Many backup applications do not read or write to cartridges that were created using a different backup application. Does the application software detect the Library?

HE designates a hard error. Be especially aware of monitoring applications, such as anti-virus software, which check every file that is read. The log shows the Date/Time, Code, and Description.