Clean CS4A 40015CS2 or CS4A sensor detects note in delivery path before/after CDU dispenses1. Exchange 1 cassette box when there are many error 4004800 The dispensed count in CS 13A and CS13B is not consistent (Cash Dispenser) 1. D170600 No Carrier during receiving data Check host. Contact your ISO or processor if you encounter an excessive amount of these errors, or you cannot complete a test transaction because of this error. check over here
Check phone number. 2. Check CS15A Sensor Cable3. Replace the CDU Board. 7710801 RMS Agent Request Time Out! Set the cassette properly 4004100Error if re-driving is over 5 times during separated rejection1. http://www.cordfinancial.com/support-center/atm-error-codes/nautilus-hyosung-atm-error-codes/
Remove any jammed bills from the dispenser, if no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). A080100 Open lever detected while executing command Remove any jammed paper. C0031 CDU Gate solenoid error The CDU did not respond to its solenoid function check. Check settings of 3 Cassette FM Board Dip Switch (#2, #4, #6 On) 972210Field is not Found1.
Initialize Pin SP. 2. Remove the jammed paper and initialize. Check notes index value. 4004400 Error if continuous 5 times are rejected 1. Hyosung 2700 Error Codes Reboot ATM. 4DN8100 Communication error of Shutter 8216091 Cash jammed on Cash Dispenser 1.
Reboot ATM. 2. Hyosung Error Code 97999(04) Do RESET at Operator Function. 2. Contact telephone company. http://atmequipment.com/s.nl/it.I/id.16/.f Reconnect CS1 sensor 4004C00In case the number of notes detected outlet sensor(CS13) is more than that of notes detected on CS1A,B sensor 4004DError of being removed 1st cassette before separate rejection 4004D00Error of being removed 1st cassette before separate rejection1.
Check Sensor(CS6) Poll3. Hyosung Tech Support ADN0100 No response detected for 30 seconds after sending command Check cable and connection between the CE and printer. Remove the remaining notes on the throat. 2. Initialize Cash Dispenser (CDU) 2.
Check if printer head lever is properly close 2010900No sensing black mark (dark sensor)1. How to fix the problem: 1. Hyosung Error Code 97999 Reinstall software. 3. Hyosung 1800 Error Codes Exchange a sensor after abnormal operating TS103 Sensor 400A100 Detected the CS9 Dark in Reject(Retract) box during initializing. (Cash Dispenser) 1.
F004F00 EPP(Pinpad) key mode is invalid 1. check my blog To show that card was inserted into the ICRW through rear side by external force 3001700To show that the card was not carried to the specific location after specified number of trial for specified time during execution of RETRIEVE command. 3001800To show that shutter open/close detection sensor(SW2) and card width check sensor(SW1) are not operating correctly. 3001900To show that a card was not inserted from the rear, even if 10 seconds had passed after the execution of BACK ENTRY command 3002000To show that track has parity error 3002100To show that read error has happened in Multiple magnetic read command. 3002200To show that write error is detected through write/verify procedure. 3002300To show that only SS,ES,LRC are contained in the track. (no retry) 3002400To show that the card has no magnetic track(no retry) 3002500To show that quality error(Jitter,Preamble,Postamble) has happended in write verify. 3002600To show that the track has no SS. 3002700To show that the track has no ES 3002800To show that the track has no LRC error 3002900To show that the discordance of write data has happened in write verify. 3003000To show that power down(or power cut in short instant)is detected(or being detected). 3003100To show that DSR signal was turned to OFF(communication is cut) 3004000To show that the card was pulled out form ICRW through entrance date when CAPTURE command is being executed. 3004100Failure at IC Contact solenoid or sensor ICD. 3004300Card could not be set to IC contack position/Failure at sensor PDI. 3004500ICRW lost sight of the card when ICRW completed to carrry the card to dhe rear position during the card acceptance, and ICRW ejected the card to entrance gate. 3004600To show that the ejected card has not been withdrawn during execution of Monitoring for removal command. 3005000Retract counter overflow. 3005100To show that Motor error has happened, through start/stop check in Initialize command. 3005300To show that read error in Digital Decode Read Command. 3006000To show that there found abnormal condition on the power-line. 3006100The receiving error for ATR. 3006200To show that the specified protocol does not agree with that of ICC/SAM ICRW still connected. 3006300In case T=1 cards, after ATR receiving, IFS exchange is failed. Check Index of notes4. Check if the CS9 sensor cable is disconnected. 3. Epp Error Atm
Check and reseat all belts. Check the replenished amount and replenish. 2. Reboot ATM. 9740102 In case nonexistent Note Index is set 9741100 When sensing CS2 Dark (Error code, 400FF00 is subdivided by location of sensor.) 9741400 When sensing CS4A Dark (Error code, 400FF00 is subdivided by location of sensor.) 9741800 When sensing CS4B Dark (Error code, 400FF00 is subdivided by location of sensor.) 9742100 When sensing CS21A,B Dark (Error code, 400FF00 is subdivided by location of sensor.) 9742800 When sensing CS13 Dark (Error code, 400FF00 is subdivided by location of sensor.) 9743B00 When sensing CS15A,B Dark (Error code, 400FF00 is subdivided by location of sensor.) 9744700 Cash picking-up fail while cash in cassette #1 is enough 1. this content Check abnormal clutch.4.
Mount the retract box or open the box cover2. Hyosung Error Code 9799904 D160300 Disconnected by Out of Order 1. If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust).
Remove a dust and foreign objects on CS11AB, CS21AB, CS31AB and CS41AB sensors.2. Remove dusts in CS13A and CS13BSensor3. Check if the CS10AB and CS14 sensor cable is disconnected.3. Hyosung Error Code 97418 Check the remaining notes in 2 Cassette2.
Check CDU Information after reading CDU version2. Check modem and modem cable connection. 2. Check the AP version and initialize 2080AThe size of image print data is abnormal1. http://orgias.org/error-code/i-o-error-codes.html Call your attendant 9701070Create Mutex Fail for SIU(Sensor)1.
Read data of ÔRead Double SensorÕ Command 40038Error in checking SRAM 40039Gate operation sensor (CS3) error1. Check notes dispensed and rejected 2. C0014 CDU sensor is tripped Similar to the COO11 error, this would indicate a bill jam close to the exit of the CDU or near the reject bin. Check if the CS31AB sensor cable is disconnected3.
Check Cash Dispenser Unit information.2. If error occurs when checking CS10A/CS10B (CDU B/D CN2 #17~24) disconnection and operation, replace a sensor. 400AC00 CS 53 sensor is detected dark due to bill jam. Our Services Mobile ATM Solutions ATM Advertising Cash Vaulting Sales Branding Franchise Opportunities Online Store Service Call Form Customer Support Stay Connected © 2016 - Empire ATM Group Shopping Cart Home (888) 225-9184 Call Today! Get the trace file and log files in D:\trace 2.
D005500 Incorrect Pin Check the transaction from the host and try again. Remove the receipt paper jam2. Clean CS1A and CS13 40030Failed in checking the main motor echo1. D009200 System Unavailable Check the transaction from the host and try again.
Reinstall software 3. Replace hard disk drive 9719400Invalid Cash Unit ID1. Remove a jammed note between the tray and Cash Dispenser. 2. Check the catcher inside cassette #1 guide 4004D00Error of being removed 1st cassette before separate rejection 4004EError of being removed 2nd cassette before separate rejection 4004EDetected the remaining notes on the return path during dispense reserved operation1.
Check cash dispenser 9745500System power off while dispensing 9770011Receive data failCheck Cable / Device 9770012Send data fail 9770013Serial port close failCheck Cable / Device 9770016Receive data timeoutCheck Cable / Device 9770017Send data timeoutCheck Cable / Device 9770032Registry write fail 9770034Registry delete fail 9770040Thread create fail 9770043Thread close fail 9770050ComMonitor4WBA.EXE create fail 9770060Shared Memory creation fail 9770111Transmitting incorrect command 9770121No defined currencyRun ÔOpenConnectionÕ again 9770122Not setting deposit direction, and Inquire Accept() methodSet direction using Direction() method 9770123Not setting deposit denomination, and Inquire Accept() methodSet denomination using Enable() method 9770124Set incorrect denomination when executing Enable()/Disable()Set correct denomination after confirming currency 9770125Set incorrect direction when executing Direction() methodSet correct direction 9770150Call Direction()/Enable()/Disable() method under no initializationAfter initialization, execute method 9799301MCU RETRACT OVERClear the count of retracted card at OP mode 9799499DISPENSER COUNT ERRORCheck the sensor on cash dispenser 9799601PBM RETRACT OVER 9799901DOOR CHECK1. Reboot ATM 2. Remove dust in CS13 Sensor 3. C0059 Cash cassette 2 removed prior to dispense.
Remove the remaining notes and foreign objects at the position of the CS31B sensor.2. Check the abnormal communication cable. 3. Contact to technician support team.