Turn the power off before attempting any adjustment! This process will clear the PC board of the error and if the filters were the culprit, your spa should start heating and running normally. Check the water temperature with an accurate temperature thermometer. Sensor plugged into jack B is not working.SnS = Sensors out of balance. http://orgias.org/error-code/htc-evo-4g-error-code-104.html
Pump may also be deactivated). drops.HL = High limit switch tripped. Another thing that you want to check is your skimmer and the filter area. If the pump is not running but the diaphragm is closing the contact you're going to get FLC because it's closed when it's not supposed to be. http://www.spadepot.com/spa-error-codes.htm
Please try the request again. Heater is deactivated.F2 = 4 hours daily filtrationF4 = 8 hours daily filtrationF6 = 12 hours daily filtrationFC = continuous filtration EasyPak Control Systems for Spas or Hot Tubs: C = CelsiusCL = Current Time of DayECdu = Economy Mode DurationEcon = Economy Mode Turn OnF = FahrenheitFldu = Filter Cycle DurationFlon = Filter Cycle Turn OnFLC = Pressure Switch AlarmFLO = Pressure Switch AlarmFrEE = Freeze Protection AlarmHL = High Temperature AlarmLoc = Panel / Keypad LockedPrH = Temperature Sensors AlarmPrr = Temperature Sensors AlarmTu = Temperature Set CelsiusTu = Temperature Set Fahrenheit Gecko Control Systems for Spas or Hot Tubs: FLO = Pressure switch failure, switch open FLC = Pressure switch failure, switch closed Prr = Temp sensor failure Prh = Hi-limit sensor failure HL = Sensor measuring 119° F FrE = Possible freeze condition detected Invensys Controls for Watkins Hot Springs and Tiger River Spas or Hot Tubs: Green Logo "Ready" indicator blinking = Heater Temperature sensor problem.Blue Logo "Power" indicator blinking = Heater high-limit thermostat tripped.Entire spa is inoperative = Check power source• Reset GFCI; call for service if it will not reset• Disconnect power for at least thirty seconds to reset heater high limit. Contact ACC. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.
The temp sensor is the larger of the two silver bullets. You can also have something called a pressure switch located on your heater element which does the same thing. The Flo code was still there. Hydropool Hot Tub Error Codes If water level is not the problem you should remove the filter cartridges from the spa.
SL = Sleep mode Brett Aqualine Control Systems for Spas or Hot Tubs: OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° FFL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp sensor E2 = Shorted hi-limit sensor E3 = Open hi-limit sensor E4 = Shorted flow switch E7 = Improper electrical connection CTI Control Systems for Spas or Hot Tubs: th1/39 = On startup indicates temperature probe problem.th2/current temperature = On startup indicates temperature probe problem.th3/39 = On startup indicates water temperature less than 39° F.OH = Overheating, water over 112° F. Hot Tub Error Codes The first thing that you want to do if you get these error codes, is actually take your breaker and turn it off and then turn it back on. Recently the FL code came up.
Well sorry about long post any any misspelled words.
I replaced the mother board twice, the motor and wet end, I've tried 3 new flow switches, new filter, new topside control, new hot and cold sensors. Marquis Spa Error Codes Loading... Please try again later. Any ideas on what to do?
If pump 1 was turned on due to this reason alone, this message will appear for up to two minutes right after very cold water is detected.Note: Internal freeze protection only functions when there is proper power running to the spa, and the control system is operational.The Panel Displays IC , iCE:This indicates that the auxiliary sensor detects a possible freeze condition. check my blog Rating is available when the video has been rented. pump will operate continuously until the temperature rises above 45° F.OH = Over heat. Please try the request again. Vita Spa Error Codes
Changing it, I mean, I don't think we need to go too far into it. If it has a seperate circ pump than maybe that is bad?-Jay Pam April 20, 2016 at 1:42 pm There is just one pump and it runs both speeds without issues. Used hot tub tonight, ran jets, when I went to put cover back on I noticed FLO code back on. this content ACC (Applied Computer Controls)Systems for Spas or Hot Tubs: CoLd = Temperature in the spa heater housing is below 40° F.
Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Great Lakes Hot Tub Error Codes If it is circulating on low speed and will not engage to high speed it could be the motor as well. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog".
I have removed and cleaned the filter, just in case. Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Hot Tub Error Code Oh Check out the tunes hereConnect with Jay on Google + 33 Comments Bob Oltman October 21, 2011 at 8:06 am Hi.
Contact qualified service technician. If you did have a filter in, for example, and you got something caught in the system, that can cause a FLO error. If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open (as best you can). have a peek at these guys I cleaned the filter and was wondering is it possible for any debris to get past filter.
Anyway not positive but possible number 2 pump never worked this year, but I think LF and dry started after leaves were in tub. Thanks Bob Mark July 16, 2015 at 9:52 pm I have a Vita Spa. admin January 5, 2016 at 1:55 pm Sorry for the delay was away for the holiday weekend.It could be the dip switches are not set correctly to your configuration. I went counter clockwise onn the adjustment and thought I had resolved the problem.
Inspect these first: Check slice or ball valves. Note: This auxiliary freeze protection functions at all times, even when another fault condition has occurred and has otherwise shut the spa down. The purpose of your pressure switch is to measure pressure in the line when your pump is running. I can reset the switch by removing one of the wires but coontinue to get the FLC or FLO readout.
Once I hooked the topside control panel back in, nothing displayed in the red led screen. ICE2 = Freeze protection. The final problem could be the pressure switch/flow switch itself. Before we get into what causes a flow error and how to fix it I should probably explain what a low flow actually is.What is a hot tub flow error?On either side of your spa's heater there are two sensors that read the water pressure flowing through the system.
Oregon Hot Tub 38,354 views 4:00 How To Fix the Air Lock on Your Hot Tub Pump | Arctic Spas - Duration: 1:33. The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. If you are unsure of something or have any questions, please do not hesitate to contact us via Email. For further troubleshooting click here.
Lise James 148,843 views 10:45 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09. Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on. If the water gets too low and the spa's filter well is not completely submerged it can cause air to be drawn into the system giving you a low flow error.How to troubleshoot a low flow errorSo lets say you go out to your hot tub, lift up the cover and you notice the temperature is low and your topside control is flashing some lights at you and reads "lo flo", what do you do now? It wants to - I keep hearing ‘clicking' as if something's trying to engage - but all that happens is that the temp indicator keeps rising to the point that the system shuts down to prevent overheating.
Sign in to make your opinion count. Can I keep adjusting it ? Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires. I can feel the pump running when power is on but nothing comes out in tub.When I check for flow with power off…nothing seems to be clogged.