Home > Error Code > Hp Printers Error Codes

Hp Printers Error Codes

Contents

On HP 4/4+/5 printers the high voltage contacts can be dirty or misaligned. If a controller board needs replacing you may need an engineer. Replace the memory chip cable/connector or the DC controller. Turn on the printer. have a peek here

This information applies to Asia Pacific only. HP Error Code:81 - Defective Network Card or Formatter Board Explanation:Your printer has a defective accessory of some kind, possibly related to memory, I/O cards or a firmware issue. The fuser possibly overheated. 50.7 Fuser pressure release mechanism failure. Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. More about the author

Hp Laptop Error Codes

Back Error 11 - Paper Out Paper tray empty or not seated correctly. Sprache: Deutsch Herkunft der Inhalte: Deutschland Eingeschränkter Modus: Aus Verlauf Hilfe Wird geladen... Fuser heater cut-off. All printers May be temporary error.

If the printer is returned to HP, the print sample must be returned with the printer. Check the tab on the bottom of the toner cartridge facing you as you open the printer. What to do:These faults typically needed assistance from an experienced HP engineer. Hp Printer Error Code Oxc4eb827f On all other printers it can be several things: DC controller, formatter, main motor Error 56 On the IID/IIID the output selector knob on the rear assembly is not in the duplex position.

Reseat same No disk installed. Hp Computer Error Codes Depending on the model, a firmware DIMM may need replacing or a flash update. Wait until the warm-up period finishes and your printer is idle and silent before you proceed. http://www.hpprinterrepair.co.uk/common-hp-printer-error-codes/ If this doesn't help there may be a hardware issue.

Figure : Cleaning the electrical contacts inside the printer Wipe the electrical contact area dry with a dry, lint-free cloth. Hp Printer Error Code 0xc19a0003 There are still other HP printer error codes that may come out depending on the printer model you own. All fans are enabled to low speed operation at power on. Replace memory PCB IIP, IIP+, IIIP 53 error Unit1 - Replace top memory card 53 error Unit 2 - Replace bottom memory card IIISi, 4Si Cycle power on printer Laser malfunction, see error 51 53.xyzz Error LJ4, 4+, 4P, 4Si, 4V Replace SIMM as indicated X = 0 ROM X = 1 ROM Y= 0 Internal memory (Formatter PCB) Y = 1 SIMM slot 1 Y = 2 SIMM slot 2 Y = 3 SIMM slot 3 Y = 4 SIMM slot 4 4L Error in RAM.

Hp Computer Error Codes

The error 10 indicates a problem with the printer obtaining the information from this chip. read this post here The printer might go through a warm-up period. Hp Laptop Error Codes Replace DC Controller PCB. Hp Inkjet Printer Error Codes Some of the checkpoints referred to in this document require special tools or meters as well as familiarity and training on laser printers.

Error 16 Toner low Toner cartridge is low on toner. navigate here Search Windows for your printer model name, and then click the printer name in the list of results. There is a tab on the front of the toner cartridge that could also cause the problem. Printer got tired of waiting for user interaction like a manual feed. Hp Printer Error Codes Ink System Failure

Simplify the print job by removing font changes and/or graphics. Reseat any SIMMs or replace if necessary. Also check motor cable connections. Check This Out The computer is turned off.

HP Error Code:66 - External Paper Handling Device Error Explanation:This fault means there's a problem with one or more additional paper or envelope trays or finishing units, such as a staple finisher. Hp Officejet Error Codes HP IIP/IIP+/IIIP could be either the laser pca or the scanner motor. If your printer uses 4 ink cartridges, type CN643A If your printer uses 5 ink cartridges, type CN642A Follow the online instructions to order the printhead assembly.

See service manual to initialize NVRAM 68 Memory IIISi, 4Si, 4V Bad SIMM memory.

HP Error Code:24 - Job Memory Full Explanation:Too many print jobs have been send to the printer, or the job is too complex for the printer memory to process. Gather the following materials: A clean, lint-free cloth A clean, dry cotton swab Distilled or bottled water caution: Do not use tap water because it might contain contaminants that can damage the printhead. Replace if necessary. Hp Deskjet Printer Error Codes press (no menu is diaplyed), press top-left, top-bottom, top-left, top-left.

Error 80 Improper MIO connection - look at pins on formatter MIO connection Defective MIO Card - Replace card Defective Formatter Card - Replace card Error 89 The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the proper location and oriented properly This can also be a temporay error, try power cycling the printer The PostScript ROM's/SIMM are defective Reprinted with permission from laser-service.com Tweet Customer Service Order Status Returns & Refunds Help Center FAQs Warranty Recycle Ink Cartridges Epson Ink Coupon Code Buy 3D Printer Help & Support Best Printers Blog Buy Printers Printer Driver Info How To Fix Printer Bluetooth Printer Tips to Save Ink Lost Printer Installation Disk Ink Types Compatible Ink Cartridges Replacement Ink Cartridges Generic Inkjet Cartridges Generic Ink Versus OEM MICR Laser Toner Inkjet Refill Kits Search for Ink by Printer 3D Printing Printer Problems Printer Not Responding How to Clean Printer Heads HP Printer Reviews Ink Cartridge Tips Inkjet Paper Fix Gaps & Lines Pigment Ink versus Dye Corporate About Us Press Green Certification Printer Industry News Expert Interviews Copyright © 2016 - Castle Ink 37 Wyckoff St. The printer prints a test page when the printhead cleaning completes. Worn pick up rollers and/or separation pad. this contact form Press and hold Power button in front3.

Replace appropriate fan as needed. Incompatible memory card in rear slot IIP, IIP+, IIIP 57 error Unit 1 - Incompatible memory in top slot 57 error Unit 2 - Incompatible memory in bottom slot LJ4, 4+, 4L, 4P, 4V, 5P Reseat cables and motor connector Replace main motor Replace DC controller PCB 57.x Service IIISi, 4Si x = 1 Gears seized Faulty top cover switch Faulty AC kill switch operation Check connector J010 on DC controller PCB Bad main motor or main motor PCB x = 2, 3 or 4 Faulty fan motor. When an indicator shows low-ink levels, consider having a replacement ink cartridge available to avoid possible printing delays. Wait until the printer is idle and silent before you continue.

Welcome visitor number since 10/17/1997 02 Warming Up (If longer than 3 minutes) Also see error code 50. 2686A/D Replace DC power supply/Main motor driver assy. Paper jams can occur at four stages: pickup, printing, fusing and exit. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. There may be a problem with connection between the memory chip and DC controller.