Home > Error Code > Hp Laser Jet Printer Error

Hp Laser Jet Printer Error

Contents

This can happen when printing a FAX document formatted for A4 size paper. Measure between the two heavy gauge pins on the fuser assembly connector. If the paper crinkles right at the toner cartridge it is most likely the drive gear located on the right side of the printer. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. http://orgias.org/error-code/hp-laser-printer-error.html

Can be defective or simply need to be reseated. Simplify the print job. Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over the oblique roller cover. No part of this site, or its source code, may be reproduced in any way.*Some Restrictions apply. JavaScript seems to be disabled in your browser.

Hp Laptop Error Codes

The product was delivered just a few minutes ago. Simplify the job by removing font changes etc. Common on the LJII/III series is a worn input pickup roller. We have seen this failure on machines with either very low page counts - 2-3K pages or between 8-12K pages.

Configure is properly. System error 87:13 Unable to read the carriage encoder sensor. System error 03:10 A problem has occurred with the printers power supply. Hp Printer Error Code Oxc4eb827f Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum!

On LaserJet's 4250, 4350 series you need to wait until you turn the power on and the memory starts counting before you hold the checkmark button. Hp Computer Error Codes HP IIP/IIIP and Apple Personal LaserWriter's that pickup the paper and then crunch it up at the toner cartridge usually have a bad drive gear assembly. We stock ample parts to repair HP Laser-Jet printer with 10:10 memory error, 41.3 paper size error, 49, 494C06 firmware error, 50.1, 502, 50.3, 50.4, 50.5 fuser error, 51.1, 51.2 beam detect error, 52.1, 52.2 scanner error, 53 memory error, 60.2, 60.3 and 60.4 lifter motor error Our technicians have the knowledge and technical ability to reset maintenance kit error codes and perform printer maintenance service on HP LaserJet 4000/4050/4100/ 4101mfp, LaserJet 4200/4300, 4250/4350/4240, P4014/P4015/P4515, M601/M603/M603 printers, 11x17 Laser Jet 5000/5100/5200, HP 8000/5Si, LaserJet 8100/8150, LaserJet 9000/9040/9050/9040mfp/9050mfp repairs, Color LaserJet 4600/4650/4610, 4700/4730mfp, 4345mfp/M4345mfp numerical error messages. You may now slide the lamp out of the fuser assembly.

System error 62:03 Parallel port communication problem System error 63:03 LAN card communication problem. Hp Printer Error Code List Pdf Printer malfunctions with failures with printing problems, such as paper jam, wrinkled copies, defective prints, grinding noise can be fixed by replacing Maintenance Kits. You must have JavaScript enabled in your browser to utilize the functionality of this website. Most HP Laser Jet printer failures can be fixed by replacing maintenance kits, fuser units, transfer kits and drum kits.

Hp Computer Error Codes

The thermal fuse and thermistor are also possible causes of a 50 Service error. https://www.marketpoint.com/hp-printer-error-codes.aspx You may be trying to print envelopes whilst in duplex mode
5. Hp Laptop Error Codes temporality for around 1 day it ran as before, but again ERROR 12. Hp Inkjet Printer Error Codes Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants.

You should hear a definite clicking. Check This Out Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP supply item How did we do? Other causes include poor quality parallel cables, poor connections, or specific software programs. Another clue can be a "clicking" sound just prior to the error 50 appearing. Hp Printer Error Code 79

If this is successful, you have a problem with the optional I/O card and should replace it or reset it. If error persists, scanner may need replacement. What to do:Removing and reinstalling the toner cartridge normally resolves the problem. http://orgias.org/error-code/hp-laser-jet-error-codes.html If the coating on the roller is damaged, the entire assembly should be replaced.

Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot. Hp Printer Error Code 0x610000f6 HP DJ 500 System error 01:13 A problem with the Electronics module has occurred. Be careful with labels, use only labels designed to take the heat generated by the fuser assembly.

Also verify the configuration through the menus on the printer.

Scroll through items until "I/O =" appears and use the +/- key to display parallel and the enter key to select. Replace device which triggers error. If you do hear the motor reach speed and then you receive and error 51 you may have a defective laser diode although this is fairly rare. Hp Printer Error Code 49 John D.

Look for smooth or cracked worn surfaces. System error 81:11 Paper-axis shutdown (during the paper advance test). Back back to top How did we do? have a peek here Error Code 13, 13.1, 13.2, 13.3 Paper Jam/Paper Jams 13.20 error code paper jam or bad paper feed drive assembly.

If the first four lights, top to bottom, are lit, press and hold the GO and RESET buttons. this error only shows at the time of initialization has finished. You will have to remove the covers to do this. On the left end of the assembly you will see the ceramic lamp end with a white wire connected to a terminal.

On the II and III Series and the IIISi/4Si, make sure at least one of the two drum sensitivity tabs are present. low line voltage causing the power supply circuits to drop out of regulation. System error 05:09 (DJ 500 only) Formatter installed instead of HP-GL/2 accessory card. These are small rectangular blocks of plastic which contact the switches in the printer.

ERROR 53 - Service On the HP Laserjet 4L/4ML/5L this error is indicated by the data light on and all others off. 4L/5L 1. The warm-up period timed out. On the LJII/III series the rubber damper on the clutch release solenoid can degrade and become sticky and gummy. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly.

HP Error Code:51 - Beam Detect Error Explanation:On older model this normally indicates the tab on the bottom of the cartridge that opens the laser shutter is missing/snapped off. Also check motor cable connections. System error 65:03 Generic input/output port communication problem. Check the paper path for toner or paper dust buildup.