X=2: Laser malfunction. 52 ERROR (Incorrect Scanner Speed) 1. Took the cartridge from the 4200 and put in the 4000 laserjet and it works fine. Wird geladen... Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. http://orgias.org/cartridge-error/hp-officejet-j5780-cartridge-error-message.html
Stage 4: Cleaning The next stage is where the OPC drum is cleaned. It sounds like all the searches (dogpile, google, yahoo) I have done maybe wrong. If you still get the message or the page is blank, the the first thing to try would be the controller board. Can also be DC controller. 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor faulty, check fan number X or duplexor fan and replace as necessary 5 Main motor failure - replace main motor 4+ 57.1 Gears are siezed, motor is bad or DC controller is bad 4Si/IIISi 57.1 Gears siezed, faulty top cover switch, faulty AC interlock switch, J010 loose or faulty, bad main motor PCA LJ 4000/405 An error occurred with the Fan's motor.
Error 22 Error/ I/O Config Error/ Par I/O Error/MIO Error 22 EIO X BUFFER OVERFLOW The EIO card in slot X has overflowed it's buffer and data loss will occur 22 EIO X BUFFER OVERFLOW - The printer parallel buffer has overflowed during a busy state. Sign Up Login Add Question BobWerner asked Jul 18, 2005 at 12:06pm 0 HP LaserJet 4100 HP Laserjet 4100 "install toner cartridge" error message I support a company with a HP LJ 4100 that continues to display "install toner cartridge." What I have tried:1) Several toner cartridges including a new one out of the box and a known working one -> no effect2) cold reset of printer -> no effectEverything pointes to the formatter being bad. These can be set within the Remote Control Panel.
If using genuine HP toner supplies did not resolve the issue, continue to the next step. Is is an HP cartridge or a refill? Paper path rollers worn? Replace Black Cartridge Message Hp Can also indicate a mis feed or paper not being picked up.
If anyone has had this problem on this printer and know s what I need to do to fix this it would be very much appreciated ! Install Black Cartridge Error Hp M1212nf Make sure you align the small plastic pin in the center on the oblong slot on the drum axle pin. Back back to top How did we do? by Anonymous on Apr 16, 2008 at 8:06pm Add comment Please sign in to comment 0 Thanks to everyone for this thread, I just bought a non HP toner and was having this problem.
On both cartridges we ran out of toner at approximately 8,800 pages. Install Black Cartridge Error Hp M1213nf Reseat connector J201 on Sensor PCA. 3. Furthermore, a new fuser sensor in the 4100 series actually measures the ambient room temperature! Then put the printer back online and send a test job from the host computer via the parallel cable.
Cycle power on the printer. 2. http://www.faroudjatoner.com/newsletter/RecyclingtheHP4100.html NOTE: We do not recommend using zinc sterate with this cartridge; it will stick to the PCR and cause small white voids in the printed characters. 10. Install Black Cartridge Error Hp Hi Al, I bought a Remanufactured Toner Cartridge, C8061X. Install Black Cartridge Error Hp M127fn The front contact is toner out, the back one is toner low.
Bad cassette microswitch. 2. Check This Out Rt. Remove and reinstall the supply, replace the supply. If not replace the motor or drive circuit as required. Install Black Cartridge Error Hp M127fw
You need to check the configuration of your printer and drivers, reset the printer, try issuing an initialization command from within the application. I stuck some cardboard in the sealing strip slot on our 4200. Short the pin closest to the front of the printer. (The printer must be turned off.) II, IID, III, IIID Only: 1. Source On some printers you can press the select button to try to continue.
Install a toner cartridge to prevent this message from displaying. Install Black Cartridge Error Hp M126nw This is sure to be a favorite of your customer service people! by unknown on Apr 12, 2010 at 4:28am Add comment Please sign in to comment 0 That's how I worked around 54.1 "remove sealing tape"Cover the chip on new catridge with aluminium foil.Insert new cartridge.
Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1. In some instances, electrical noise in the cable can corrupt data during transmission to the printer. Replace cable, Fuser to DC Controller, connector J206. (P/N RG1-0907-000.) 2. Hp Laserjet Pro Mfp M127fn Install Black Cartridge Error Figure : Inserting the toner cartridge Reconnect the power cord, and then turn on the printer.
This is direct from HP, they say if the formatter goes, it will usually take the firmware with it. The INFORMATION MENU should appear on the display. They are attached to the cover, and can only be removed if you press the tabs in. have a peek here Hot water sets toner into the fabric.
For example, once the machine sends a "Toner Out" signal to the cartridge, the chip is set for "Yes" for Toner Out as indicated on the supplies status page (more on that later). Back back to top How did we do? If resetting the printer did not resolve the issue, continue to the next step. If this sensor fails, the printer will signal a 58.2 error.